G.R.A.S. 43AE Instruction Manual Download Page 4

Page: 4 / 17

Introduction

The 43AE Ear Simulator Kit is for acoustically testing supra-aural

earphones, telephone hand-

sets and loudspeakers, and complies with the following international requirements:



ITU-T Recommendation P.57 (08/96) “Serie P: Telephone Transmission quality. Objective
measuring apparatus: Artificial ears”.

Components

43AE Ear Simulator Kit

The 43AE Ear Simulator comprises the following main components:



RA0045 IEC 60318-4 Ear Simulator with 40AG microphone included

, see page 4



26AC

¼” Preamplifier



RA0001 ¼” - ½” Adapter



RA0056 Low-leak Pinna Simulator



RA0057 High-leak Pinna Simulator

43AE-S1 Ear Simulator Kit prepolarized

The 43AE-S1 uses the same componets as the 43AE except:



RA0045 IEC 60318-4 Ear Simulator with 40AO microphone included



26CB

¼” Preamplifier

When assembled as shown in Fig. 1, it is ready for testing supra-aural earphones, telephone
handsets and loudspeakers.

26AC
¼" Preamplifier

RA0045
IEC 60318-4

Coupler

RA0001
¼" - ½” Adapter

Caution! When attach-

ing RA0001 to the

RA0045, use only

gentle finger force.

Fig. 1.

Assembled 43AE Ear Simulator Kit

An earphone applied externally to the ear

LI0070 – 28 June 2017

Summary of Contents for 43AE


















Search results

Summary of Contents for 43AE

Reviews:

Related manuals for 43AE

Brands by name

Popular brands

G.R.A.S. 43AE, Instruction Manual

Search results

Summary of Contents for 43AE

Reviews:

Related manuals for 43AE

Brands by name

Popular brands