background image

9

LI0010 – 1 October 2015

Technical Specifications

The AC Outputs for Microphones and Electrostatic Actuator

Under open loop conditions, the AC outputs of the 14AA are linear to over 200 kHz. However, 
the cable connected to the output limits the high-frequency performance in the same way as a 
low-pass filter. The longer the cable, the lower the cut-off frequency. If you need to measure at 
very high frequencies, you must use the shortest cable possible. When the high-frequency roll off 
is known, you can use it as a correction factor. 

The 

AC Output

 (O VDC for prepolarized microphone) 

Output Signal, max level peak-to-peak

100 V RMS

–3 dB Low Frequency Cut-off
    Open loop

0.35 Hz

    1 M 

 load

1.9 Hz

Frequency Response, 1 meter RG-58 cable (~100 pF), 100 V RMS
    ± 0.1 dB

25 – 50 kHz

    ± 1 dB

10 – 100 kHz

Max Output Current

5 mA AC

The 

AC 200  VDC 

(for externally polarized  microphone)

Output Signal

100 V RMS

–3 dB Low Frequency Cut-off
    Open Loop

0.3 Hz

    1 M

 load

1.8 Hz

Frequency Response, 1 meter RG-58 cable (~100 pF), 100 V RMS
    ± 0.1 dB

25 – 50 kHz

    ± 1 dB

10 – 100 kHz

Max Output Current

5 mA AC

DC Output Impedance*

5.6 M

* See also schematic drawing in Fig. 2

Summary of Contents for 14AA













Reviews: