FUTABA T32MZ, Instruction Manual

Page: 47 / 189

47
＜
Model Basic Setting Procedure
＞
4. Throttle cut setting
(
In case of engine model
)
Throttle cut can be performed with one touch by a switch
without changing the throttle trim position.
Set throttle cut with the Throttle Cut function of the Linkage
Menu. After activating the throttle cut function and selecting
the switch, adjust the throttle position so that the carburetor
becomes full close. For safety, the throttle cut function operates
the throttle stick in the slow position.
5. Idle down setting
(
In case of engine model
)
The idling speed can be lowered with one touch by a switch
without changing the throttle trim position. Perform this setting
with the Idle Down function of the Linkage Menu. After
activating the Idle Down function and selecting the switch,
adjust the idle down speed. For safety, the idle down function
acts only when the throttle stick is in the slow position.
*While the Throttle Cut function is in operation, the Idle
Down function does not work.
6. AFR (D/R)
AFR function is used to adjust the throw and operation curve
RIWKHVWLFNOHYHUDQGVZLWFKIXQFWLRQVIRUHDFKÀLJKWFRQGLWLRQ
This is normally used after End Point (ATV) has defined
the maximum throw directions (End Point acts on all flight
condition settings). When mixing is applied from one channel to
another channel, both channels can be adjusted at the same time
by adjusting the operation rate through the AFR function.
7. Airbrake
This function is used when an air brake is necessary when
taking off or diving, etc.
7KHSUHVHWHOHYDWRUVDQGÀDSVFDPEHUÀDSEUDNHÀDSRIIVHW
amount can be activated by a switch.
7KHRIIVHWDPRXQWRIWKHDLOHURQHOHYDWRUDQGÀDSVHUYRVFDQ
be adjusted as needed. Also the speed of the aileron, elevator,
and flap servos can be adjusted. (IN side/OUT side) A delay
can be set for each condition, and a cut switch which will turn
2))WKHGHOD\FDQEHFKRVHQ7ULPDPRXQWVFDQEH¿QHWXQHG
by setting a VR. You can also set the auto mode, which will link
Airbrake to a stick, switch, or dial. A separate stick switch or
dial can also be set as the ON/OFF switch.
$GGLWLRQRIÀLJKWFRQGLWLRQV
7KHWUDQVPLWWHUFDQLQVWDOOXSWRHLJKWÀLJKWFRQGLWLRQVSHU
model. You can assign all switches including sticks, switches,
WULP OHYHUV DQG WULP VZLWFKHV DV IOLJKWFRQGLWLRQ VHOHFWLRQ
switches. You can also add delayed mixing to these functions
in order to avoid sudden changes. Moreover, you can set
SULRULW\RUGHUIRUÀLJKWFRQGLWLRQVZKHQ\RXVHWPRUHWKDQRQH
condition. In addition, you can copy conditions and/or change
QDPHVRIFRQGLWLRQV7KLVFRPPDQGPD\DOVREHXVHGWRGH¿QH
what switches and/or controls are used to activate each flight
condition.
The Condition Select function automatically allocates the
condition 1 for each model type. Condition 1 is the default
condition, also referred to as normal, and is the only one active
ZKHQDQHZPRGHOW\SHLVGH¿QHG7KLVFRQGLWLRQLVDOZD\V21
and remains ON until other conditions are activated by switches.
The Condition Delay can be programmed for each channel.
The Condition Delay is used to change the servo throw smoothly
when switching conditions.
*When a new condition is added, "Condition1" data is
automatically copied.
*Select the condition switch and set the new condition data
with the switch in the ON position. However, if the group
mode (Gr.) was selected in advance, the same data will be
input to all new conditions. Select the single mode (Sngl)
and adjust the condition you want to change.
$,53/$1(
*/,'(5