R7114SB
●
Applicable systems: Futaba FASSTest-2.4GHz / FASST-Multi-ch system
transmitter
◆
FASSTest-2.4GHz Bidirectional Communication System / FASST-Multi-ch 2.4GHz
◆
S.BUS2 / S.BUS Port and 12 Channels (+DG1,2) for Conventional System Receiver
◆
with High gain antenna
1M23N36202
Usage precaution
• Analog servos cannot be used with the R7114SB in the FASSTest
12CH mode.
• When the FASST Multi-ch High-speed Mode is used, analog servos
cannot be used at the CH1
〜
6 outputs for convention systems. How-
ever, in other than the FASSTest 12CH mode, analog servos can be
used at CH7
-
12, DG1 and DG2 at any time.
• Don't connect to Extra Voltage Telemetry Port before turning on a re-
ceiver.
WARNING
Changes or modification not expressly approved by the party
responsible for compliance could void the user’ s authority to operate the
equipment.
The R7114SB receiver should be protected from vibration by foam
rubber, Velcro, or similar mounting methods. Protect from moisture.
Antenna installation precaution
Do not cut or bundle the receiver antenna wire.
Do not bend the coaxial cable. It causes damage.
The antennas must be mounted in such a way to assure they are strain
relieved.
Keep the antenna as far away from the motor, ESC and other noise
sources as you possibly can.
Be sure that the two antennas are placed at 90 degrees to each other.
■
The R7114SB has two antennas. In order to maximize signal reception and
promote safe modeling Futaba has adopted a diversity antenna system. This allows
the receiver to obtain RF signals on both antennas and fly problem-free.
Antenna installation for carbon fuselage
You must leave 30mm at the tip of the antenna fully exposed. The
exposed antenna should be secured so that it cannot move around or
back inside of your aircraft.
Be careful of connector insertion
Don't connect an S.BUS servo / gyro to S.BUS2 connector.
Do not connect the power supply battery to other than the power
supply connector.
■
There is the danger of ignition, explosion, or burning.
Link precaution
Do not perform the linking procedure while the motor's main power is
connected or the engine is operating as it may result in serious injury.
When the linking is complete, please cycle the receiver power and
ensure the receiver is properly linked to the transmitter.
Please power up your system in this order. Transmitter first, followed
by the receiver.
If the R7114SB receiver was previously linked to another transmitter,
make sure that transmitter is not operating while linking the receiver to
the new transmitter.
R7114SB
Link/Mode
switch
Antenna
Mode LED Link LED
Extra Voltage
Telemetry Port
Thank you for purchasing a Futaba
R7114SB
FASSTest-2.4GHz
compatible receiver.
The
R7114SB
receiver features bi-directional communication with a
FASSTest
Futaba transmitter using the
S.BUS2
port. Using the
S.BUS2
port an impressive array of telemetry sensors may be utilized. It also includes both standard PWM output
ports and
S.BUS
output ports. The
R7114SB
can also be switched to the
FASST-Multi-ch
System.
R7114SB Specifications
FASSTest-2.4GHz
system(14ch/12ch mode)
FASST-2.4GHz
system (Multi-ch mode)
S.BUS2
and
S.BUS
port and Linear 12ch +Digital 2ch for conventional
system receiver
• Dual antenna diversity
• Size: 1.98 x 1.45 x 0.63 in. (50.2x37.0x15.9 mm)
• Weight: 0.77 oz. (21.9 g)
• Power requirement: 3.7 V to 7.4 V (Voltage range: 3.5 V to 8.4 V)
• Battery F/S Voltage: FASSTest:It sets up with a transmitter
FASST: 3.8 V *The Battery F/S voltage is set for 4-cell NiCd/NiMH bat-
tery. Battery F/S function doesn't work properly when other type battery
is used.
• Extra Voltage port: 0 V-70 V DC
CH1-12 Servos
Default : S.BUS port
It's possible to change to DG2.
S.BUS2
S.BUS
DG2
DG1
1-12
channel
Hub
S.BUS2equipment
Telemetry sensor
Telemetry sensor
The receiver power supply can
be connected to any port.
Battery
3.7Ｖ-7.4V
Switch
Servo
Y-harness
When all ports are used.
Connection
Connector
The direction of the
connectors of the
bottom 3 ports is
different by 90˚.
LED Indication
System Mode LED
Status
Link LED
FASSTest
Green
Solid
No signal reception
Red Solid
Receiving signals
Green Solid
Waiting for link
Start → 2 seconds later →
Red Blink（1second）
FASST
Off
No signal reception
Red Solid
Receiving signals
Green Solid
Receiving signals but ID is unmatched
Green Blink
Waiting for link
Red Blink
FASSTest
FASST
－
Unrecoverable error (EEPROM, etc.)
Alternate blink
90°
Antenna
installation
Do not bend the antenna part
Gently bend the coaxial
cable part.
Fix the sleeve to the model
Antenna part
Sleeve
Coaxial cable
Declaration of Conformity (for EU)
Hereby, Futaba Corporation declares that the radio equipment type is R7114SB in compliance with Directive 2014/53/
EU. The full text of the EU declaration of conformity is available at the following internet address:
http://www.rc.futaba.co.jp/english/dl/declarations.html
Compliance Information Statement (for Canada)
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure
limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum dis-
tance 20cm between the radiator & your body.
French: Cet appareil radio est conforme au CNR-210 d’Industrie Canada. L’utilisation de ce dispositifest autorisée
seulement aux deux conditions suivantes : (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit
être prêt à accepter tout brouillage radioélectrique reçu, même sice brouillage est susceptible de compromettre le fonc-
tionnement du dispositif. Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un
environnement non contrôlé.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de ray-
onnement et votre corps.
Compliance Information Statement (for U.S.A.)
This device, trade name Futaba Corporation, model number R7114SB, complies with part15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: To assure continued FCC compliance
1. Any changes or modifications not expressly approved by the grantee of this device could void the user's authority
to operate the equipment.
2. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
The responsible party of this device compliance is:
FUTABA Corporation of America
2681 Wall Triana Hwy Huntsville, AL 35824, U.S.A.
Phone:1-256-461-9399 FAX:1-256-461-1059 E-mail: [email protected]
低功率射頻器材技術規範 3.8.2 警語
取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變更
原設計之特性及功能。
低功率射頻器材之使用不得影響飛航安全及干擾合法通信 ；經發現有干擾現象時，應立即停用，並改善至
無干擾時方得繼續使用。
前述合法通信，指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及
醫療用電波輻射性電機設備之干擾。
