When S.BUS is used
* Set the channel of
S.BUS
servos by using an
SBC-1
channel changer,
CIU-
2
USB serial interface or the programming software resident in the
18MZ
transmitter.
*
Can also be used together with conventional servos. However, conventional
servos cannot be used by the
S.BUS
output.
*
When using servos with a remote battery pack, use
S.BUS
Hub with Cable
(2-way/remote battery pack use).
Please refer to the instruction manual of
S.BUS
Hub with Cable (2-way/re
-
mote battery pack use) for the connection method.
*Turn on the power in transmitter→receiver order. In addition, always check
the operation of all the servos before flight.
*Do not insert or remove the servo connector while the receiver power is ON.
WARNING
Do not perform the linking procedure while the motor's
main wire connected or the engine is operating as it may
result in serious injury.
When the linking is complete, please cycle the receiver
power and ensure the receiver is properly linked to the
transmitter.
Please power up your system in this order. Transmitter
first, followed by the receiver.
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
Link to the transmitter
1
Press and hold the
Link/Mode
switch more than two(2) seconds.
Re-adjust the 3CH F/S position (only for TM-8)
1
Press and hold the
Link/Mode
switch between one(1) and two(2)
seconds.
0 to 1 sec.
1 to 2 sec.
More than 2 sec.
0 sec.
1 sec.
2 sec.
Press and Hold
No function
With
TM-8
(not included in this set)
To set the F/S
position(No re-link)
Re-link(ID set) and to
set the F/S position
No function
Other than
TM-8
(not included in this set)
Re-link(ID set)
•
If there are many FASST systems turned on in close proximity, your receiver
might have difficulty establishing a link to your transmitter. This is a rare
occurrence. However, should another FASST transmitter/receiver be linking at
the same time, your receiver could link to the wrong transmitter. This is very
dangerous if you do not notice this situation. In order to avoid the problem,we
strongly recommend you to double check whether your receiver is really under
control by your transmitter.
Channel Modes
The R6308SBT is capable of changing its channel allocations as
described in the table below.
1
Press and hold down the Link/Mode button on the R6308SBT receiver.
2
Turn the receiver on while holding down the Link/Mode button.
After power up, the button can be released.
3
The LED should now be blinking red in one of the patterns described
by the chart below.
4
Each press of the Mode/Link button advances the receiver to
the next mode.
5
When you reach the mode that you wish to operate in, press
and hold the Mode/Link button for more than 2 seconds.
6
Once locked into the correct mode the LED will change to a
solid color.
7
Please cycle the receiver(s) power off and back on again after
changing the Channel Mode.
S.BUS2
S.BUS2
extends
S.BUS
and supports bidirectional communication.
Sensors are connected to the
S.BUS2
port. Sensor information is
transmitted to telemetry receiver unit by which the option is carried out.
*Only S.Bus2 capable devices may be connected to the S.Bus2 port.
Standard S.Bus servos and gyros should not be connected to the S.Bus2
port.
High speed mode / Telemetry ON, OFF
R6308SBT can perform the change of high speed mode and a normal
mode. A response becomes high-speed, however the high speed mode
cannot use a sensor. Only receiver battery voltage transmits.
Mode and Telemetry
Operation Mode
Telemetry
Normal
Receiver battery voltage, Sensor
High speed
Only receiver battery voltage
1
Turn the receiver on
.
2
Press and hold down the Link/Mode button on the R6308SBT receiver.
3
A button will be released, It held for 10 seconds and LED became red
high-speed blink.
R6308SBT
Normal/High speed mode・Telemetry ON/OFF
Link/Mode
Press and Hold
Transmitter turn OFF
Release
More than 10sec.
0S
5S
SW
(Red blink) (Red/green blink)
(Red high speed blink)
(LED)
10S
1S
4
Each press of the Mode/Link button advances the receiver to
the next mode.
5
When you reach the mode that you wish to operate in, press
and hold the Mode/Link button for more than 2 seconds.
6
Once locked into the correct mode the LED will change to a red
green simultaneous blink.
7
Please cycle the receiver(s) power off and back on again after
changing the Channel Mode.
*If you use two receivers by one model, please make Telemetry ON into one set.
Receiver Mode table
Mode
Normal
High speed
Telemetry
ON
OFF
ON
OFF
Green LED blink
1time
2time
3time
4time
Link to the Telemetry Receiver Unit (option)
Since it links with telemetry receiver unit (option), R6308SBT is made
into ID transmitting mode.
1
Turn the receiver on
.
2
Press and hold down the Link/Mode button on the R6308SBT receiver.
3
A button will be released, It held for 5 seconds and LED became red
green blink .
R6308SBT
ID transmitting mode
Link/Mode
Press and Hold
Transmitter turn OFF
Release
More than 5sec.
0S
5S
SW
(Red blink)
(Red/green blink)
ID transmitting mode
(LED)
30S
1S
4
Red green blink of the R6308SBT is carried out, and it goes
into ID transmitting mode for 30 seconds.
5
Telemetry receiver unit (option) is linked between ID
transmitting mode.
*Refer to the manual of telemetry receiver unit (option) for link operation of telemetry
receiver unit .
Output
connector
Channel
Mode Ａ
1 ～ 8CH
Mode B
1 ～ 7CH
Mode C
9 ～ 16CH
Mode D
9 ～ 15CH
1
1
1
9
9
2
2
2
10
10
3
3
3
11
11
4
4
4
12
12
5
5
5
13
13
6
6
6
14
14
7/B
7
7
15
15
8/SB
8
S.BUS
16
S.BUS
Red LED
blink
1 time
2 time
3 time
4 time
R6308SBT CH Mode table
©FUTABA CORPORATION 2012, 2 (1)
