Compliance Information Statement (for U.S.A.)
This device, trade name Futaba Corporation of America, model number R614FF-E, complies with part15 of the
FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: [email protected] (Support)
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
R614FF-E Specifications:
(
FASST
system, 4-channel receiver)
• Receiving on 2.4GHz band
• System:
FASST-C2
system
At Normal/High speed mode (auto detection)
•
Receiving Range : 70m (230ft.)(at the best conditions)
• Power requirement Rated voltage: 3.7V-7.4V / Usable voltage: 3.5-8.4V
• F/S and Battery F/S function:It is set according to the transmitter used.
• Battery F/S voltage: Set it with the transmitter arbitrarily.
• Size: 1.38x0.91x0.35” (35.1x23.2x9.0mm)
• Weight: 0.27oz. (7.6g)
WARNING
NEVER
use dry batteries for the
power supply of the
R614FF-E
as this
may cause difficulties with the receiver's
operation.
NEVER
use the
R614FF-E
in GP
cars.
Wrap the receiver with something
soft,such as foam rubber,to avoid
vibration. Do not splash water over the
receiver.
Since the receiver generates a
certain amount of heat, install the
place with good ventilation.
Link Procedure
Each transmitter has an individually assigned,
unique ID code. In order to start operation, the
receiver must be linked with the ID code of
the transmitter with which it is being paired.
Once the link is made, the ID code is stored in
the receiver and no further linking is necessary
unless the receiver is to be used with another
transmitter.
1
Place the transmitter and the receiver
close to each other within half (0.5) meter.
2
Turn on the transmitter and the receiver.
3
Push and hold the Link switch on the
receiver.
4
When the link is complete, the LED on the
receiver changes to solid green.
* Please refer to the table below for LED status
and receiver condition.
No signal reception
LED: Red
Receiving signals
LED: Green
Receiving signals, but ID
is unmatched.
LED: GreenBlink
Unrecoverable failure
(EEPROM,etc.)
LED: Red and Green
turn on alternately
* If there are many
FASST
systems turned on
around your receiver, it might not link to your
transmitter. In this case, even if the receiver’s
LED stays solid green, unfortunately the
receiver might have established a link to
one of the other transmitters. This is very
dangerous if you do not notice this situation.
In order to avoid the problem, we strongly
recommend you to double-check whether
your receiver is controlled by your transmitter
by giving throttle input, etc. and then checking
servo response.
WARNING
After the linking is done, please
cycle receiver power and check if
the receiver to be linked is really under
the control by the transmitter to be
linked.
D o n o t p e r fo r m t h e l i n k i n g
procedure with motor's main wire
connected or with the engine operating
as it may result in serious injury.
Link switch
LED
Battery / DSC
terminal (B/C)
CH output (1 to 4)
Operating Precautions:
Once the
R614FF-E
detects the
FASST
normal mode or
FASST
high
speed mode , the detected mode is
locked as long as the power is ON.
When need to change the mode,
please cycle power.
Note:
The R614FF-E is compatible with the FASST-C2 system
transmitters (Futaba T4PK/T4PKS).
*Futaba FASST system does not work with current Futaba S-FHSS/FHSS system.
Usage condition on "High Speed mode"
CAUTION
When using the high-speed mode, use a Futaba
digital servo (including brushless servo). Analog
servos cannot be used.
• The use of analog servos may cause servo trouble.
FASST-2.4GHz System
Built-in Antenna
4-Channel Receiver
for EP Car Models
Thank you for purchasing the
R614FF-E
receiver.
The
R614FF-E
is designed for use with the Futaba
FASST-C2
system transmitter. The
FASST
system has
two(2) operation mode as shown below.
•Normal mode/High Speed mode
The "Normal mode" accepts any type of servos or
the peripheral equipment. The "High Speed mode"
only accepts the digital servos, including BLS series,
and most peripheral equipment such as the brushless
ESCs. However, there is a transmitter that cannot
correspond, to high speed mode.
Please pay special attention to the information
contained within this manual and transmitter's manual
in order to have a pleasant running experience.
•Built-in antenna
The
R614FF-E
receiver is designed to be used only for
EP Car models.
T he R61 4 FF-E is co mp atible with the
FASST-C2 system transmitters.
R614FF-E
1M23N17457
©FUTABA CORPORATION 2011, 11 (1)