manualshive.com logo in svg

FUTABA GY701, Installation Instructions Manual

Share
Download
FUTABA GY701 Installation Instructions Manual Download Page 60

G

OVERNOR 

S

PEED 

S

ETTING

60

The GY701 is used by connecting the “rpm” input 
to the governor speed setting channel of your sys-
tem. When using an independent governor on/off 
switch, activate the “(6) Governor on/off switch” 
funtion within the “

Governor Basic Setting

” section 

earlier in this manual. (S.BUS connection only)

Direct set by transmitter on Gov. mixing

 When governor mixing as in the T14MZ and 

T12FG is used to switch the RPM of the rotor 
head speed. The head speed can be switched 
with each condition or the switch.

*For a description of the governor mixing, refer to 

your transmitter’s manual.

Using by 3position switch

 Set the RPM at each switch position in the “(2) 

Revolution setting” menu within the “

Gov-

ernor Basic Setting

” section earlier in this 

manual.

Speed setting precautions

s7HENTHESPEEDSETTINGCHANNELTRAVEL%0!!46

!&2 ISSETTOORLESSPOINTSANDCANNOT

be set.

s4HE ENGINE MAXIMUM SPEED RANGE LIMITS THE

maximum speed setting.

s4EST FLY THE HELICOPTER WITH THE GOVERNOR TURNED

OFFANDTACHTHEMAINROTOR20-WHILEINHORI

-

ZONALmIGHT4HISISTHEMAXIMUM20-THATCAN

be achieved with the engine and pitch setup that 
you are using. Please set the governor maximum 

SPEEDTOAPPROXIMATELY20-SLESSTHANMAX
20-%XAMPLE)F20-SISMAXTHENSET

Summary of Contents for GY701
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands