NOTICE
Do not drill through the cradle when drilling the pilot holes.
This may damage the cradle.
3
Secure the cradle to the mounting surface using two 4 gauge
(3 mm) countersunk stainless-steel screws.
Installing the Batteries
You must install AAA alkaline batteries (not included) in the
remote control.
1
Slide the battery door to the back of the remote, and pull
up to open it.
2
Insert two AAA batteries, observing polarity.
3
Slide the battery door back onto the remote to close it.
Remote Control Operation
LED power on (
)
Hold to turn off all color LEDs and turn on the warm and cool
white LEDs.
LED power off
LED color-selection wheel (
Changing the Color of the LEDs
Light: activates when the remote sends a signal to the receiver
LED brightness or speed
Static color: changes the brightness (
)
Dynamic mode: changes the speed between color changes
(
Changing the Speed of a Display Mode Pattern
)
Warm white LEDs (
Cool white LEDs (
)
LED dynamic mode (
Changing the Display Mode of the LEDs
Turning the LEDs On and Off
After you connect the remote control receiver to the speaker
LEDs, you must use the remote control to turn the LEDs on and
off.
1
Press .
The LEDs connected to the receiver turn on with the same
color and mode settings applied before the last time you
turned them off.
2
Press to turn off the LEDs connected to the receiver.
Changing the Color of the LEDs
1
If necessary, turn on the LEDs for the speakers you want to
change.
2
Select an option:
• Touch the color wheel to select a new color, and slide
your finger to fine-tune it.
• Hold to change the LED color to white.
NOTE:
This turns off all color LEDs and turns on the cool
white and warm white LEDs.
Changing the Brightness of the RGB LEDs
1
If necessary, turn on the LEDs for the speakers you want to
change, and select a color.
2
Select an option:
• To increase the LED brightness, press above
.
• To decrease the LED brightness, press below
.
Using Cool or Warm White LEDs
You can use the remote control to add cool or warm white to any
color, or on their own.
• To add or remove warm white LEDs to or from a color, press
.
• To add or remove cool white LEDs to or from a color, press
.
• To turn off all color LEDs and turn on the warm and cool
white LEDs, hold
Changing the Brightness of the Warm or Cool White LEDs
1
If necessary, turn on the warm or cool white LEDs for the
speakers you want to change.
2
Select an option:
• To increase the LED brightness, press above
or
.
• To decrease the LED brightness, press below
or
.
Changing the Display Mode of the LEDs
You can cycle through a pre-defined set of LED flashing,
breathing, or color-changing effects (
).
1
If necessary, turn on the LEDs for the speakers you want to
change.
2
Press .
3
Press to change to the next mode in the sequence.
4
Touch a color on the color wheel to stop the display mode
and return to a solid color.
Display Mode Options
You can select among 25 different color and transition patterns.
When you reach the end of the cycle of display modes by
continually pressing , the patterns stop, and the LEDs are a
static full white. When you press again, the cycle starts at the
beginning.
Display mode 1 Red, green, and blue fade in and out
Display mode 2 Red, green, blue, yellow, teal, magenta, and full
white fade in and out
Display mode 3 Full white fade in and out
Display mode 4 Cool white fade in and out
Display mode 5 Warm white fade in and out
Display mode 6 Cool white and warm white fade in and out
Display mode 7 Red, cool white, and warm white fade in and out
Display mode 8 Green, cool white, and warm white fade in and out
Display mode 9 Blue, cool white, and warm white fade in and out
Display mode 10 Red, green, blue, cool white, and warm white fade in
and out
Display mode 11 Red, green, blue, yellow, teal, magenta, full white,
cool white, and warm white fade in and out
Display mode 12 Full white, cool white, and warm white fade in and out
Display mode 13 Red, green, and blue strobe
2
Wireless CRGBW LED Remote Control Instructions
