manualshive.com logo in svg

Furuno FS-1570, Service Manual

Share
Download
Furuno FS-1570 Service Manual Download Page 196

 

 

6.5 TEST function in DSC SETUP menu 

 

6-20 

TX/RX PCB test 

Test mode and the test frequency are set to adjust PLL and to confirm receiver sensitivity. 
SYS ADJ CH sets the frequency for PLL adjustment and SEN CHK CH for receiver 
sensitivity check. The channel frequency can be changed. 18MHz receiver test signal is 
switched on/off by using TEST SIG line. 
The frequency on FREQ SWEEP line is set by rotating the knob.

   

 

 

W/R PCB test 

This menu is similar to TX/RX PCB test menu. SYN ADJ CH is used to adjust PLL on W/R 
board and SEN CHK CH to check the receiver sensitivity of W/R board.   
 

 

 

TA TEST 

This test is used at type approval. 

 

 

Summary of Contents for FS-1570



































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands