background image

Page 2 of 10

BASIC ASSEMBLY TECHNIQUES

FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.

       PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.

FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY

   RESULT IN INJURY AND/OR PROPERTY DAMAGE.

IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO

SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.

When lock or spring washer is used in
an assembly, please make sure the

lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.

Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.

FURNITURE OF AMERICA.ALL RIGHTS RESERVED.

Make sure all parts are properly

aligned, then use the appropriate

hand tool to completely tighten the
bolts or screws. Do not use power

tools and do not overtighten.

Position each part correctly and insert

screws or bolts into their respective

holes by hand tighten or using the
proper hand tool. Only tighten when

step is completed or when instructed
to do so.

Save the instructions and store the Allen

wrench or any supplied tool for later

maintenance. After two weeks, check and

tighten any loose hardware and repeat
again every six months thereafter.

Use cardboard or carpet area when

assembling furniture to prevent
scratches 

.

Make sure the furniture

rests on a flat and level surface with
each leg evenly touching the floor.

Summary of Contents for CM7394Q





















Reviews: