RR-15 and RR-15NL Features
The RackRider RR-15 and RR-15NL are the perfect
accessories for any rack-mount system. Install a RR-15 or
RR-15NL in the top slot of your rack, and the eight switched AC
outlets on the rear panel will safely power up all your equipment.
The RR-15 features two slide-out, swiveling light fixtures which
provide discreet illumination of your equipment on stages and in
studios, while a dimmer control (“Rack Lights”) lets you adjust the
lamp brightness to just the right level.
The RR-15 and RR-15NL protect your delicate electronic
equipment by combining a high voltage varistor (MOV) surge and
transient suppressor with an RFI/EMI interference filter. The fast-
acting suppression circuit responds in less than a nanosecond,
clamping transient voltages to safe levels. The filter works to
prevent noise from fluorescent lights, certain dimmers, radio
transmitters, and similar sources of “electronic pollution” from
contaminating the AC line and from there, leaking into sensitive
audio, video, or computer circuits.
Maximum Load
The eight circuit breaker protected outlets are rated at 15 Amps,
which is equivalent to 1800 Watts at 120 volts. If the total load on
the RR-15 or RR-15NL (combining all outlets) exceeds 15 Amps,
the circuit breaker (located on the rear panel) will trip, cutting off
power to your rack. If this happens, reduce the load by unplugging
one or more units from the RR-15 or RR-15NL. Then push the
circuit breaker button in to reset it.
Lamps
The RR-15’s lamps pull out easily and may be aimed to
provide the best illumination for your equipment. They come
supplied with 7 Watt night-light bulbs. Replacements are readily
available at most hardware stores or almost anywhere household
light bulbs are sold. Bulbs are easily replaced without removing
the unit from the rack by unscrewing the cap on the end of each
light tube. The caps and light tubes become quite warm to the
touch in normal operation. Be careful not to push the tubes in while
the caps are unscrewed.
If you find that the heat from the tubes is excessive, try
reducing the setting of the Rack Lights knob. As an alternative,
you may wish to substitute 4-Watt bulbs or even colored
Christmas tree bulbs.
RR-15 Power Conditioner and Light Module
RR-15NL Power Conditioner
Switches
The RR-15 and RR-15NL each have a master switch for the
rear outlets which glows when the power is on. The RR-15 lights
turn off automatically when the tubes are pushed in.
Limited Warranty
Furman Sound, Inc. • 1997 South McDowell Blvd. • Petaluma, California 94954-6919
Phone: 707-763-1010 • Fax: 707-763-1310 • http://www.furmansound.com • e-mail: [email protected]
0014C
The RackRider RR-15 is warranted by Furman Sound, Inc. against
failures due to defective parts or faulty workmanship for a period of
ninety (90) days after delivery to the original owner. During this
period, Furman will make any necessary repairs without charge for
parts (except bulbs) or labor. However, shipping charges to the repair
facility must be prepaid by the owner. This warranty applies only to
the original owner and is not transferable. Also, it does not apply to
repairs done other than by the Furman repair facility listed below.
This warranty may be cancelled by Furman at its sole discretion
if the unit has been subjected to physical abuse (including but not
limited to connection to improper AC or DC voltages), or has been
modified in any way without written authorization from Furman.
Furman’s liability under this warranty is limited to repair or
replacement of the defective unit.
Furman will not be responsible for incidental or consequential
damages resulting from the use or misuse of its products. Some states
do not allow the exclusion of incidental or consequential damages,
so the above limitations may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which
vary from state to state.
Before returning any equipment for repair, please be sure that it
is adequately packed and cushioned against damage in shipment,
and that it is insured. We suggest that you save the original
packaging and use it to ship the product for servicing. Also, please
enclose a note giving your name, address, phone number and a
description of the problem.
All equipment returned for repair must have a Return
Authorization (R.A.) Number. To get an R.A. Number, please write,
call, or fax the Furman Service Department at the address below,
between 8 a.m. and 5 p.m. U.S. Pacific Time. You may be asked to
provide a copy of the original purchase invoice showing the purchase
date. Please display the R.A. Number prominently on the front of your
package.
BY
