background image

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be deter-
mined by turning the equipment off and on, the
user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment

and receiver.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is
connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

- 4 -

EN

9I03

PRECAUTIONS

PRECAUTIONS

LOCATION

For safe operation and satisfactory performance of
your TV/VCR, keep the following in mind when
selecting a place for its installation:

Shield it from direct sunlight and keep it away
from sources of intense heat.

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes
at the top or bottom of the unit. Do not place the
unit on a carpet because this will block the ventila-
tion holes.

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the TV/VCR near strong magnetic fields.

Avoid moving TV/VCR to locations where temper-
ature differences are extreme.

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting
it from an AC wall outlet. Grasp it by the plug.

If by accident, water is spilled on your unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.

Do not put your fingers or objects into the
TV/VCR cassette holder.

Do not place anything directly on top of the unit.

WARNING

Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place
or after heating a cold room or under conditions of
high humidity. If a tape is played in a TV/VCR
which has moisture, it may damage the tape and
TV/VCR. Therefore when the condensation occurs
inside the unit, turn the POWER button on and allow
at least 2 hours for the unit to dry out.

IMPORTANT COPYRIGHT INFORMATION

Unauthorized recording or use of broadcast televi-
sion programming, video tape, film or other copy-
righted material may violate applicable copyright
laws. We assume no responsibility for the unautho-
rized duplication, use, or other acts which infringe
upon the rights of copyright owners.

FCC WARNING- This equipment may gener-
ate or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction man-
ual. The user could lose the authority to oper-
ate this equipment if an unauthorized change
or modification is made.

The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial
number as yours. You should record the number and other vital information here and retain this book as a per-
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.

All manuals and user guides at all-guides.com

Summary of Contents for esa RSEC313E

































Reviews: