2
Custom settings
Lock your desk
With a Memory Preset handset, your desk can be lock in place at any height.
To lock: Press and hold the M button for about 8 seconds. The display will first change to S -, then to LOC,
indicating that the desk is now locked.
To unlock: Press and hold the M button for about 8 seconds until LOC goes away and the height appears on the
display.
Adjust the height readout
Our LED handsets display the approximate height of your desk top surface, in inches or centimeters. The accu-
racy may be affected by the thickness of your top, the evenness of your floor, etc. If you want it to be completely
accurate, you can manually set the readout to match your measured height.
1.
Press and hold the DOWN button until the desk reaches its lowest position. Release.
2.
With your favorite measuring tool, measure the distance from the floor to your desk top surface.
If it matches your readout, you’re all set. Otherwise, proceed to the next step.
3.
Press and hold the DOWN button again, until the display flashes RST (looks like “AS
Γ
”). Release.
4.
Press and hold the M button until it begins to flash the starting height. Note: the display will revert to RST
after about 5 seconds. If that happens before you have a chance to make your changes, just press and hold
M again.
To change the readout height:
5.
Use the UP or DOWN button to adjust the display by 0.1 inch at a time until the display shows the correct
height, as measured.
6.
Wait about 5 seconds and the display will automatically return to RST, which indicates Reset Mode.
7.
Complete the reset process by pressing and holding the DOWN button again while the desk lowers a little
bit more, slightly rises, and then stops.
8.
Release the button, and you should see the new starting height
±
.1 inches. This height is saved, and your
desk is ready to use!
3
Set custom upper and lower height limits
By default, the Remi frame and handset are set to allow the maximum range of motion — from a fully retracted
Lifting Column to a fully extended one. If you would like to set a higher minimum height or a lower maximum
height, you can do that! Before starting, make sure the desk is plugged in, and the LED display is showing a
number. If the readout has gone dark, you can wake it up by pushing any button. If it is displaying something
besides a number, perform the Reset Procedure on page 5.
To set the upper limit:
1.
Use the UP/DOWN buttons to move the desk to the desired maximum height.
2.
Press the M button and release, then press the UP button and release. The display will flash S - to show that
it is ready to set the upper limit.
3.
Press and hold the M button for about 2 seconds. The display will show “999” and then return to the height
readout. This indicates that the upper limit is set. All done!
To set the lower limit
1.
Use the UP/DOWN buttons to move the desk to the desired minimum height.
2.
Press the M button and release, then press the DOWN button and release. The display will flash S - to
show that it is ready to set the lower limit.
3.
Press and hold the M button for about 2 seconds. The display will show “000” and then return to your
selected height. This indicates that the lower limit is set. You did it!
Warning: There are certain times when your desk might require a Reset Procedure to correct a balance,
calibration or other issue. This procedure requires the legs to retract completely, beyond any lower height limits
that might be set. Please ensure that you have the proper clearance below the desk base.
Note: If you had previously set any memory presets that were outside of your newly defined range, they won’t
work anymore. You can reuse the numbers.
2nd Note: If you want to set a new upper or lower limit that is outside of your set range, you will first have to
restore the defaults.
To restore default upper and lower limits
1.
Press the M button and release. “S -” will appear on the display.
2.
Within 5 seconds, press the M button again and hold for about 2 seconds until the display shows “555”.
3.
Release the button. The display will automatically change back to the height display, and your height limits
will reset.
