W
ARRANTY
- FULL
GAUGE CONTROLS
Products manufactured by Full Gauge Controls, as of May 2005, have a two (02) year
warranty, as of the date of the consigned sale, as stated on the invoice. They are guaranteed
against manufacturing defects that make them unsuitable or inadequate for their intended
use.
EXCEPTIONS TO WARRANTY
The Warranty does not cover expenses incurred for freight and/or insurance when sending
products with signs of defect or faulty functioning to an authorized provider of technical
support services. The following events are not covered either: natural wear and tear of parts;
external damage caused by falls or inadequate packaging of products.
LOSS OF WARRANTY
Products will automatically lose its warranty in the following cases:
- The instructions for assembly and use found in the technical description and installation
procedures in Standard IEC60364 are not obeyed;
- The product is submitted to conditions beyond the limits specified in its technical
description;
- The product is violated or repaired by any person not a member of the technical team of
Full Gauge Controls;
- Damage has been caused by a fall, blow and/or impact, infiltration of water, overload
and/or atmospheric discharge.
USE OF WARRANTY
To make use of the warranty, customers must send the properly packaged product to Full
Gauge Controls together with the invoice or receipt for the corresponding purchase. As much
information as possible in relation to the issue detected must be sent to facilitate analysis,
testing and execution of the service.
These procedures and any maintenance of the product may only be provided by Full
Gauge Controls Technical Support services in the company's headquarters at Rua Júlio de
Castilhos, 250 - CEP 92120-030 - Canoas - Rio Grande do Sul – Brasil
Rev. 03
ENVIRONMENTAL INFORMATION
Packaging:
The materials used in the packaging of Full Gauge products are 100% recyclable. Try to
perform disposal through specialized recyclers.
Product:
The components used in Full Gauge controllers can be recycled and reused if
disassembled by specialized companies.
Disposal:
Do not incinerate or dispose the controllers that have reached the end of their service as
household garbage. Observe the laws in your area regarding disposal of electronic
waste. If in doubt, please contact Full Gauge Controls.
Copyright 2016
13. ANNEXES - Reference Images
Image V
Image VI
Image VII
Y
X
CONTROLLER
LOCKS
PANEL
CONTROLLER
CONTROLLER
VINYL
PANEL
12.
INTEGRATING CONTROLLERS, RS-485 SERIAL INTERFACE
AND COMPUTER
A
B
MT-530
super
A
B
MT-530
super
A
A
B
B
A B
A
B
A
A
B
B
A B
A
A
B
B
A B
A
A
B
B
A B
*Connecting Block for Serial Communication
Used to connect more than one instrument to the Interface. The wire's connections must
be made in agreement with the following rules: terminal
A
of the instrument connects to
the terminal
A
of the c
, that must be connected with the terminal
A
of the
Interface. Repeat the action for terminals
B
and
, being
the cable shield.
onnecting block
the terminal of onnecting block must be connected to the respective terminals of
each instrument.
c
*Sold Separately
CONV. 32
or
CONV. 256
Keep Sitrad updated in website:
http://www.sitrad.com
®
Watch Sitrad installation video in:
http://www.fullgauge.com/
videos/sitrad
9. DISPLAY SIGNALINGS
Sensor 1 disconnected or damaged.
Sensor 2 disconnected or damaged.
Sensor 3 disconnected or damaged.
Sensor 4 disconnected or damaged.
Functions lockdown activated.
Functions lockdown disabled.
Contact Full Gauge Controls.
Reconfigure the values of the functions.
[Err1]
[Err2]
[Err3]
10. GLOSSARY OF ACRONYMS
- °C:
Temperature in Celsius degrees.
- °F:
Temperature in Fahrenheit degrees.
- LOC:
Blocked.
- No:
No.
- OFF:
Turned off/disabled.
- ON:
Turned on, enabled.
- SET (as in "Setting")
(setting or configuration).
- Vac:
Electrical voltage (volts) of alternating current.
- Vdc:
Electrical voltage (volts) of direct current.
- Yes:
Yes.
[Err4]
[LOC,][On,,]
[LOC,][OFF,]
[eCAL]
[pppp]
Extended frame
It allows the installation of Evolution line
controllers with sizes 76 x 34 x 77 mm in
many differents situations, since it does
not require precision in the notch of the
instrument fitting panel.
The frame integrates two switches of
10 Amperes that may be used to
actuate interior light, air curtain, fan,
and others.
Ecase protective cover
It is recommended for the Evolution line, avoids water from
entering the back part of the instrument. It also protects the
product when the installation site is washed.
11. OPTIONAL ITEMS - Sold Separately
ECASE PROTECTIVE COVER
CONTROLLER
EXTENDED FRAME
SWITCHES
- version 2 or higher
EasyProg
It is an accessory that has as its main function to store the parameters of the controllers. At any time, you
can load new parameters of a controller and unload them on a production line (of the same controller),
for example. It has three types of connections to load or unload the parameters:
- Serial RS-485:
It connects via RS-485 network to the controller (only
for controllers that have RS-485).
- USB:
it can be connected to the computer via the USB port, using
Sitrad's Recipe Editor.
- Serial TTL:
The controller can be connected directly to
EasyProg
by the TTL Serial connection.
EASYPROG
