background image

En-4

6.1.  Connecting the transmission cables

(1)  Turn off the power of the connecting unit.
(2)  Insert the driver, etc. into the hole (For open case) and open the top 

cover.

Push

Open

(3)  Connect the transmission cable to accessory KNX connector to con-

nect to KNX network.

(4)  Connect the KNX cables to (+) and (-) according to the polarity of the 

master unit.

(5)  Connect the connector cable for indoor unit to the speci

fi

 ed connector 

fi

 rmly.

(6)  Securely tighten the cable tie and then con

fi

 rm that the cable will not 

come out.

(7)  Use the 3 screws (M4 × 16 mm) provided to mount this product to the 

behind ceiling, wall, 

fl

 oor or other suitable location.

(8)  Once the wiring of the cables has been completed, 

fi

 t the 2 hooks of 

top cover and close the cover.

2 hooks

* The hole for a cable can be widened as necessary. When passing the 

thick cable through the hole, widen it.

Connector cable
to Indoor unit

KNX cable

KNX 
connector

Cable tie

Tightening strength

Cable tie 

0.3 to 0.5 N

(2.7 to 4.4 lbf)

(3 to 5 kgf)

Fix the connector cable even outside the main unit as necessary. Fix the 
cable with cable tie using 3 

fi

 xing holes.

Cable tie
(Accessories) 

Holes for 

fi

 xing cable tie (3 places)

6.2. Installation method

Do not install the main unit with the cables downward.

7.  CIRCUIT BOARD SETTING

Set this product Prog Button.

(1)  Programming Button (Prog Button)

Used for communication with the ETS.

Push to toggle between the modes.
Runtime mode (Default)  

  Programming mode 

[PROG LED off] 

[PROG LED on]

9374707171-02_IM.indb   Sec1:4

9374707171-02_IM.indb   Sec1:4

28/4/2017   AM 11:14:48

28/4/2017   AM 11:14:48

Summary of Contents for UTY-VKSX







Reviews: