Fujitsu U810 - LifeBook Mini-Notebook - 800 MHz User Manual Download Page 31

Page: 31 / 176

- Status Indicator Panel

Hard Drive Access Indicator

The Hard Drive Access indicator glows green when your internal hard drive is being accessed. Note that
flickering is normal.

Power Indicator

The Power indicator glows blue when your system is turned on.

NumLk Indicator

The NumLk indicator states that the integral keyboard is set in numeric keypad mode.

CapsLock Indicator

The CapsLock indicator states that your keyboard is set to type in all capital letters.

ScrLk Indicator

The ScrLk indicator states that your scroll lock is active.

•

Batteries subjected to shocks, vibration or extreme temperatures can be permanently
damaged.

•

A shorted battery is damaged and must be replaced.

Summary of Contents for U810 - LifeBook Mini-Notebook - 800 MHz

















































































































































































Search results

Summary of Contents for U810 - LifeBook Mini-Notebook - 800 MHz

Reviews:

Related manuals for U810 - LifeBook Mini-Notebook - 800 MHz

Brands by name

Popular brands

Fujitsu U810 - LifeBook Mini-Notebook - 800 MHz, User Manual

Search results

Summary of Contents for U810 - LifeBook Mini-Notebook - 800 MHz

Reviews:

Related manuals for U810 - LifeBook Mini-Notebook - 800 MHz

Brands by name

Popular brands