Fujitsu Stylistic 4120 User Manual Download Page 15

Page: 15 / 74

G e t t i n g S t a r t e d

Figure 1-4 Stylistic ST4000 Series Tablet PC Features (Top View)

Top Features:

•

Pen:

The main input device that you use to execute

programs and enter data. A pen holder is built into
the Tablet PC to store the pen when not in use.

•

Microphone Jack:

Allows you to connect an external

microphone

†

•

Headphone Jack:

Allows you to connect a set of stereo

headphones

†

•

PC Card slot:

Allows you to install PCMCIA Cards in

the system.

•

IrDA/FIR port:

Provides an infrared interface for

communication with devices compliant with IrDA
Standard Revision 1.1.

•

USB ports:

Allow you to connect Universal Serial

Bus-compliant devices (compliant with USB
Standard Revision 1.1) to the Tablet PC. Additional
USB ports are located on the optional Tablet Dock

†

•

IEEE 1394 Jack:

Allows you to connect between your

Tablet PC and peripherals such as a digital video
camera

†

•

Air flow vents:

Provides secondary cooling for

processor. (Do not obstruct the vents.)

†

These peripherals and accessories are sold separately.

Pen Holder

PC Card Slot

PC Card

IrDA Port

USB Ports

Microphone

Headphone

IEEE 1394 Jack

Eject Button

Jack

Air flow vents

Pen Tether
Attachment Point

Alb_UG_Active B.book Page 5 Monday, October 21, 2002 12:15 PM

Summary of Contents for Stylistic 4120











































































Search results

Summary of Contents for Stylistic 4120

Reviews:

Brands by name

Popular brands

Fujitsu Stylistic 4120, User Manual

Search results

Summary of Contents for Stylistic 4120

Reviews:

Brands by name

Popular brands