manualshive.com logo in svg

Fujitsu PRIMERGY TX300, Operating Manual, Page: 43 / 127

Share
Download
Fujitsu PRIMERGY TX300 Operating Manual Download Page 43

A26361-K881-Z102-4-7619

 37

Hardware Installation

Installing/Removing the Rack Model into the Rack

Figure 7: Prepare the left telescopic rail

Ê

Fasten the delivered assembly bracket HL on the rear end of the left 
telescopic rail (1) with two screws M5x8 (2) and two hexagonal flange nuts 
M5 (3) as shown in figure 4.

When mounting the left telescopic rail in the DataCenter Rack, the supplied 
support bracket must first be mounted level with the device on the rear left 
support upright.

Ê

Mark the position of the attachment points for the telescopic rails and for the 
server (front panel) on the support uprights (four height units).

Ê

Mount the support bracket at the appropriate height on the left rear support 
upright as described in the Technical Manual of the DataCenter Rack.

Ê

Place the spring nuts to fasten the telescopic rails in the groove of the 
support uprights at the marked attachment points. 

Ê

Adjust the position of the nuts in the groove until they lock into the correct 
position.

Summary of Contents for PRIMERGY TX300
































































































































Reviews:

No comments