manualshive.com logo in svg

Fujitsu PRIMERGY TX300, Operating Manual, Page: 39 / 127

Share
Download
Fujitsu PRIMERGY TX300 Operating Manual Download Page 39

A26361-K881-Z102-4-7619

 33

Hardware Installation

Installing/Removing the Rack Model into the Rack

Figure 4: Prepare the telescopic rails with the assembly brackets

Ê

Fasten the delivered assembly bracket VL on the front end of the left 
telescopic rail (1) with two screws M5x8 (2) as shown in figure 4.

Ê

Fasten the delivered assembly bracket HL on the rear end of the left 
telescopic rail (3) with two screws M5x8 (4) and two hexagonal flange nuts 
M5 as shown in figure 4.

Ê

Repeat the procedure also for the right telescopic rail and the corresponding 
assembly brackets VR and HR.

For mounting the left telescopic rail in the PRIMECENTER Rack, the delivered 
support bracket must first be mounted on the rear left support upright. The 
bracket must be mounted level with the lower edge of the device.

Ê

Mount the support bracket at the appropriate height on the left rear support 
upright as described in the Technical Manual of the PRIMECENTER Rack.

Summary of Contents for PRIMERGY TX300
































































































































Reviews:

No comments