Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download Page 135

Page: 135 / 209

▶

"Installing the top covers" on page 56

▶

"Sliding the server enclosure into the rack" on page 68

▶

Install all HDD/SSD modules in the relevant HDD/SSD cages, see

"Installing a 2.5-inch HDD/SSD module" on page 114

▶

If applicable, install all 2.5-inch HDD/SSD dummy modules into the relevant
cage, see

"Installing a 2.5-inch dummy module" on page 117

▶

If applicable, install the front bezel, see

"Installing the front bezel" on

page 47

▶

"Installing server nodes in the server enclosure" on page 81

▶

"Installing the new hot-plug PSU" on page 101

▶

"Connecting the power cord" on page 84

▶

"Switching on the server nodes" on page 86

7.8

Replacing the HDD/SSD bridge board

Field Replaceable Unit
(FRU)

Hardware: 40 minutes

Tools:

Preliminary and concluding steps: Phillips PH2 / (+) No. 2
hexagonal cross SW5 / PZ2

Main steps: tool-less

Preliminary steps

▶

Shut down the server nodes, see

"Shutting down the server" on page 41

▶

"Disconnecting the power cord" on page 42

▶

"Removing the defective hot-plug PSU" on page 100

▶

"Removing server nodes from the server enclosure" on page 43

▶

If applicable, remove the front bezel, see

"Removing the front bezel" on

page 48

Hard disk drive (HDD) / solid state disk (SSD)

CX400 M6

Upgrade and Maintenance Manual

135

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Search results

Summary of Contents for PRIMERGY CX400 M6

Reviews:

Brands by name

Popular brands

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Search results

Summary of Contents for PRIMERGY CX400 M6

Reviews:

Brands by name

Popular brands