Fujitsu PRIMEQUEST 440 System Design Manual Download | Manualshive

Page: 99 / 280

background image

C122-B001-02EN

3-1

CHAPTER 3 General Software Configuration

1

This chapter describes the PRIMEQUEST software configuration.

, the software configuration consists of MMB firmware

installed on the management board (MMB), GSWB firmware installed on the gigabit
switch board (GSWB), and the software installed in each partition, such as the OS
(Linux or Windows), PRIMEQUEST Server Agent (PSA), and related software.

System management operations and configuration are performed from the MMB
Web-UI. All system management operations, including operations related to PSA
installed in a partition, can be performed from a Web browser running on a general-
purpose PC through linkage with a Web server using the MMB firmware.

PRIMEQUEST supports large-scale enterprise environments that require high
reliability, by ensuring close linkage between hardware and software.

Figure 3.1 PRIMEQUEST software configuration

PRIMEQUEST

MMB

MMB

MMB
Firmware

Hardware

Hardware (SB, IOU)

PAL/SAL/EFI

Hardware

Partition#0

Partition#1

Partition#n

PRIMECLUSTER GDS/

PRIMECLUSTER GLS/

PRIMECLUSTER

PSA

(PRIMEQUEST Server Agent)

Linux/Windows

GSWB

GSWB

GSWB

Firmware

Web browser

Business LAN
Management LAN

Management Integrations
- Server System Manager
- Systemwalker

«
...
97
98
99
100
101
...
»

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Reviews:

No comments

Related manuals for PRIMEQUEST 440

Express 5800 Series

Brand: NEC Pages: 90

PDS-220F Series

Brand: ICP DAS USA Pages: 94

8841 - eServer xSeries 236

Brand: IBM Pages: 100

eServer BladeCenter HS40 Type 8839

Brand: IBM Pages: 120

Server 3100 series

Brand: Digital Equipment Pages: 71

ZENWORKS PATCH MANAGEMENT 6.4 SP2 - SERVER

Brand: Novell Pages: 390

Brand: Acard Pages: 43

PRIMERGY PG-RSBOP2

Brand: Fujitsu Pages: 68

SPARC Enterprise T5440 Server

Brand: Fujitsu Pages: 92

SPARC Enterprise T5140

Brand: Fujitsu Pages: 138

SPARC Enterprise T5440 Server

Brand: Fujitsu Pages: 214

SPARC Enterprise T5140

Brand: Fujitsu Pages: 130

Brand: Fujitsu Pages: 514

EMC VxFlex Appliance R840

Brand: Dell Pages: 44

EqualLogic PS4000

Brand: Dell Pages: 73

EMC PowerProtect DD6400 System

Brand: Dell Pages: 46

EqualLogic PS5500

Brand: Dell Pages: 8

Brand: Dell Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands