Fujitsu PRIMEQUEST 440 System Design Manual Download | Manualshive

Page: 97 / 280

background image

C122-B001-02EN

2-39

2.15 Other (Options and Other Devices)

2.15

Other (Options and Other Devices)

This section describes optional products.

2.15.1

UPS

A UPS contains a battery, and it provides power to the system even in the event of a
power abnormality such as a power outage.

The main unit provides a power failure notification pin for receiving a power failure
notification from a UPS. Two power failure pins are mounted corresponding to dual
power feed (option).

In primary power feed, a UPS is connected to the CPCB UPC0 connector of the main
unit. In dual power feed, one UPS is connected to CPCB UPC0 connector of the main
unit and another UPS is connected to CPCB UPC1 connector of the main unit.

The UPS connected to the UPC0 connector must be connected with an AC cable to
the ACS of the PRIMEQUEST main unit. The UPS connected to the UPC1
connector must be connected with an AC cable to the ACS of the expansion power
cabinet. The UPS connected to the UPC0 connector is UPS #0. The UPS connected
to the UPC1 connector is UPS #1.

«
...
95
96
97
98
99
...
»

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Reviews:

No comments

Related manuals for PRIMEQUEST 440

Brand: Rack Solutions Pages: 8

Brand: Vxl Pages: 19

8649 - Eserver xSeries 225

Brand: IBM Pages: 194

eServer 380 xSeries

Brand: IBM Pages: 112

iDataPlex dx320 6385

Brand: IBM Pages: 60

UniServer R2900 G3

Brand: H3C Pages: 15

SSG-2029P-ACR24H

Brand: Supermicro Pages: 136

Brand: Vxl Pages: 2

Brand: FS Pages: 91

AcquiLite A7810-0

Brand: Obvius, LLC Pages: 29

Netfinity 4500R

Brand: IBM Pages: 60

Brand: Syncronorm Pages: 17

HAM RADIO DELUXE

Brand: Kenwood Pages: 16

TS-401T Turbo Server

Brand: QNAP Pages: 8

Brand: Black Box Pages: 66

Brand: B+B SmartWorx Pages: 24

Brand: Seeed Pages: 9

Serial Servers Vlinx VESR9xx

Brand: Vlinx Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands