Fujitsu PRIMEQUEST 440 System Design Manual Download

Page: 88 / 280

2-30

C122-B001-02EN

CHAPTER 2 General Hardware Configuration

2.10

AC Section (ACS)

This section explains the AC section (ACS).

The ACS has a redundant configuration only for the PRIMEQUEST 440 using dual
power feed.

Two power distribution board (PDB) units can be connected to an ACS unit. Three
power supply units (PSUs) can be connected to a PDB.

Two PSUs can be used with one AC cable.

The primary power feed option consists of six PSUs. Up to 12 PSUs can be
connected to the option.

The AC section supports dual power feed as an option.

Table 2.18

lists ACS specifications.

Table 2.18

ACS specifications

Item

Specifications

Input

Voltage

Rated voltage

200 to 240 VAC

Number of phases

Single phase

Fluctuation range

+10% to -10%

Frequency

Rated frequency

50/60 Hz

Fluctuation range

2%, -4%

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 440

Reviews:

Related manuals for PRIMEQUEST 440

Brands by name

Popular brands

Fujitsu PRIMEQUEST 440, System Design Manual

Search results

Summary of Contents for PRIMEQUEST 440

Reviews:

Related manuals for PRIMEQUEST 440

Brands by name

Popular brands