Fujitsu PRIMEQUEST 440 System Design Manual Download

Page: 87 / 280

C122-B001-02EN

2-29

2.9 OPL

2.9

OPL

The OPL contained in this unit has a four-LED display function.

Each LED status indicates the unit status and whether a failure has occurred.

The OPL has the following functions:

Displaying the power status of the main unit (Power-LED)

Indicating whether a unit is faulty (Alarm-LED)

Identifying the unit under operation (Location-LED)

Displaying the MMB status, for MMB status checks from outside the main unit
(MMB-Ready-LED)

Figure 2.16 OPL

Table 2.17 LED display on the OPL

LED

Color

LED status

Unit status

Power-LED

Green

Off

Power to unit is off

Power to unit is on

Alarm-LED

Orange

Off

Normal status

Unit failure

Location-LED Blue

Off

Unit cannot be recognized

Unit is recognized

Blinking

Unit is recognized

MMB-Ready-
LED

Green

Off

Power to unit is off

MMB is active

Blinking

MMB is being initialized

Power

Alarm

Location

MMB-Ready

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 440

Reviews:

Related manuals for PRIMEQUEST 440

Brands by name

Popular brands

Fujitsu PRIMEQUEST 440, System Design Manual

Search results

Summary of Contents for PRIMEQUEST 440

Reviews:

Related manuals for PRIMEQUEST 440

Brands by name

Popular brands