Fujitsu PRIMEQUEST 440 System Design Manual Download | Manualshive

Page: 157 / 280

background image

C122-B001-02EN

5-13

5.2 Main GSWB Functions

5.2.3

Spanning tree function

This function determines the dynamic relay path of a bridge relay as stipulated in
IEEE802.1D.

This function is used when a bridge network that has multiple paths between two
points is created.

The spanning tree protocol automatically constructs tree-formed logical paths
(spanning tree) including all switches based on message exchanges between switches.
If a physical loop exists, loop configuration can be avoided because ports that do not
form a tree are automatically blocked. A redundancy function, which re-computes the
tree and switches to a new path automatically whenever one part of a path is blocked
due to a failure, is also provided.

shows the difference in the system depending on whether this function is

enabled or disabled.

Figure 5.3 Spanning tree function

SW

SW

SW

SW

Partition#n

PRIMEQUEST

GSWB

Partition#n

GSWB

When the spanning tree function is disabled

When the spanning tree function is enabled

This path can be used as
a backup path at a failure.

A frame transits
within a loop.

Data can be received and
sent by the shortest path.

PRIMEQUEST

Partition#n

PRIMEQUEST

GSWB

Partition#n

GSWB

When the spanning tree function is disabled

When the spanning tree function is enabled

This path can be used as
a backup path at a failure.

A frame transits
within a loop.

Data can be received and
sent by the shortest path.

PRIMEQUEST

«
...
155
156
157
158
159
...
»

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Reviews:

No comments

Related manuals for PRIMEQUEST 440

Brand: Synology Pages: 15

eServer 380 xSeries

Brand: IBM Pages: 112

R120d-1E N8100-1954F

Brand: NEC Pages: 166

Brand: Santec Pages: 40

SuperServer 1029U-T Series

Brand: Supermicro Pages: 1

BladeCenter PS703

Brand: IBM Pages: 198

FusionServer 1288H V5

Brand: xFusion Digital Technologies Pages: 96

FusionServer 2298 V5

Brand: Fusion Pages: 89

Brand: BRONKHORST Pages: 19

DL380 Gen 10 AI

Brand: Bosch Pages: 18

Brand: Bosch Pages: 48

Brand: Bosch Pages: 44

Brand: 7th Sense Pages: 60

Brand: QNAP Pages: 58

Brand: Vxl Pages: 2

PRIMERGY econel 20

Brand: Fujitsu Siemens Computers Pages: 62

SPARC Enterprise M4000

Brand: Fujitsu Siemens Computers Pages: 162

Brand: Alcatel Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands