Fujitsu PRIMEQUEST 440 System Design Manual Download | Manualshive

Page: 137 / 280

background image

C122-B001-02EN

4-31

4.3 PSA Functions

4.3.2

Hardware configuration management

This function displays the hardware resources that form a partition.

This function displays the following configuration information:

- SB configuration, IOU configuration
- CPU configuration (maximum number of CPUs which can be mounted, CPU

mounting locations, identification information such as the CPU type, error
status information)

- Memory configuration (mounting locations, detailed information such as the

memory type, error status information)

- PCI configuration (PCI card mounting, PCI device mounting, detailed

information such as the PCI device type, error status information)

- SCSI/FC connection unit configuration (HDD, tape drive, etc.)
- Network configuration (network interfaces, error status information)

4.3.3

OS information display

This function displays information on the OS installed in a partition.

This function displays the following information:

- OS information (OS type, OS version, and package installation information)
- Storage configuration information (device and capacity information)
- Network configuration information (interface, connection state, speed, routing

information)

- OS status (operating hours and login count)
- Process list

«
...
135
136
137
138
139
...
»

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Reviews:

No comments

Related manuals for PRIMEQUEST 440

DSN-4100 Series

Brand: D-Link Pages: 2

UniServer R6900 G5

Brand: H3C Pages: 17

Brand: 7starlake Pages: 32

Brand: Jatheon Pages: 52

Brand: Speco Pages: 28

xSeries 440 8687

Brand: IBM Pages: 80

xSeries 230 6RY

Brand: IBM Pages: 194

AlphaServer ES47

Brand: HP Pages: 76

AlphaServer GS80

Brand: HP Pages: 88

Brand: HP Pages: 39

16/18-Port Cable Management Kit

Brand: HP Pages: 14

Brand: HP Pages: 49

AlphaServer ES47

Brand: HP Pages: 152

AlphaStation DS20

Brand: HP Pages: 15

AlphaServer ES45

Brand: HP Pages: 38

AB500A - Integrated Lights-Out Advanced

Brand: HP Pages: 43

AlphaServer GS1280 Systems

Brand: HP Pages: 59

2533t - Compaq Mobile Thin Client

Brand: HP Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands