Fujitsu PRIMEQUEST 440 System Design Manual Download | Manualshive

Page: 132 / 280

background image

4-26

C122-B001-02EN

CHAPTER 4 Hardware System Management

4.2.11

Setting information save and restore

This function saves and restores PAL/SAL/EFI setting information for each partition
and MMB setting information.

Separate PAL/SAL/EFI settings are required for each partition. However, using the
PAL/SAL/EFI SETUP screen to make the settings in each partition is complicated, so
as shown in

, the MMB provides a save and restore function for PAL/SAL/

EFI setting information of each partition.

This function enables the following operations:

1)

After PAL/SAL/EFI settings are made from the PAL/SAL/EFI SETUP screen in
one partition, the PAL/SAL/EFI setting information for that partition can be
saved and applied to another partition from the MMB.

2)

If a failure occurs in an SB and the SB is swapped, the saved PAL/SAL/EFI
information enables restoration of the original state.

Saved information can be stored on a remote terminal. Data saved on a remote
terminal can be restored.

In addition to the function for the PAL/SAL/EFI configuration information, a save
and restore function for saving and restoring MMB and GSWB configuration
information is provided as well.

«
...
130
131
132
133
134
...
»

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Reviews:

No comments

Related manuals for PRIMEQUEST 440

BladeCenter HS23

Brand: IBM Pages: 30

System x3950 X6

Brand: IBM Pages: 53

Brand: IBM Pages: 128

Brand: Sercomm Pages: 75

SUPERSERVER 5018D-FN8T

Brand: Supermicro Pages: 124

Brand: LevelOne Pages: 88

eserver iSeries 270

Brand: IBM Pages: 40

Brand: Atop Pages: 2

Brand: Syncronorm Pages: 17

ProLiant ML350 G3

Brand: HP Pages: 44

ProLiant ML310e Gen8 v2

Brand: HP Pages: 43

ProLiant ML330 Generation 3

Brand: HP Pages: 34

PROLIANT ML350 G6

Brand: HP Pages: 145

ProLiant ML350 Gen9

Brand: HP Pages: 171

PROLIANT ML350 G6

Brand: HP Pages: 103

PROLIANT ML330 G6

Brand: HP Pages: 137

IP-DECT SERVER 400

Brand: SpectraLink Pages: 221

Brand: innuos Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands