Fujitsu PRIMEQUEST 440 System Design Manual Download Page 126

Page: 126 / 280

4-20

C122-B001-02EN

CHAPTER 4 Hardware System Management

4.2.6

Console redirection

This function sets I/O destinations of each partition's console information through an
management LAN.

The two methods below are available for OS input and output in each partition. These
methods can be set independently in each partition:

(1)

Using the COM port of the IO_Unit incorporated in each partition

(2)

Using the management LAN through the MMB

Figure 4.14

shows the flow of console information sent when the information is

redirected to the management LAN.

Figure 4.14 Flow of redirected information

When the information is redirected to the management LAN, a terminal connected to
the management LAN can be used as a console.

MMB

HUB

Partition#0

IOU

BMM

COM

….

telnet par#n

telnet par#0

telnet par#2

HUB

Management LAN

CPU

Partition#1

IOU

BMM

COM

CPU

Partition#n

IOU

BMM

COM

CPU

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 440

Reviews:

Brands by name

Popular brands

Fujitsu PRIMEQUEST 440, System Design Manual

Search results

Summary of Contents for PRIMEQUEST 440

Reviews:

Brands by name

Popular brands