Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 48

Page: 48 / 344

3.3

Connecting and Configuring the MMB

A field engineer will have constructed a test environment for the MMB to run test programs in it. Therefore, you

need to reconfigure the MMB to switch from the test environment to that for actual operation. Skip the steps for

items already set by the field engineer.

After connecting the MMB, perform the following from the MMB Web-UI:

- Registering a user account

- Configuring security

- Setting the time ... etc.

Connect and configure the MMB by using the following procedures.

TABLE 3.1 MMB connection and configuration flow

Procedure

Item

Description

See

Connecting the

MMB console PC

Connect the MMB console PC to set up

the environment for actual operation.

3.3.1 Connecting the

MMB console PC

Initializing MMB

settings

Initialize MMB settings before setting

up the connection environment for

actual operation.

3.3.2 Initializing MMB

settings

Setting up the

connection

environment for

actual operation

The MMB is set for a test connection.

Set up the connection environment for

actual operation.

3.3.3 Setting up the

connection

environment for actual

operation

Logging in to the

MMB

There is also a description of the MMB

Web-UI window for reference.

3.3.4 Logging in to the

MMB

3.3.5 How to view the

Web-UI window

Configuring the

network for actual

operation

The MMB is set for testing purposes,

so configure the network and Web

servers for actual operation. Make the

required settings appropriate to your

operation mode.

3.3.6 Configuring the

Initializing MMB

settings

Initialize MMB settings.

- Registering a user account

- Setting the system name

- Setting the date and time

After you initialize the above settings,

we recommend backing up the setting

information. For details on how to back

up the specified information, see

3.5

Saving Configuration Information

3.3.12 Setting the date

and time

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 3 Work before Operating System Installation

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands