Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 61

Page: 61 / 344

Operations

1. Click [Network Configuration] - [Network Interface].

>> The [Network Interface] window appears. For details on the [Network Interface] window, see 1.5.2

[Network Interface] window in the

PRIMEQUEST 1000 Series Tool Reference

(C122-E110EN).

FIGURE 3.9 [Network Interface] window (example)

2. Enter values in [IP Address], [Subnet Mask], and [Gateway Address] in [Virtual IP Address]. Also specify

the host name.

Remarks

Set the physical IP addresses and virtual IP addresses of MMB#0 and MMB#1 in the same subnet.

3. Click [Enable] for [Interface] in [MMB#0 IP Address] or [MMB#1 IP Address]. Then, enter a value in each

item. Specify a physical IP address to assign it at this time.

4. Specify the required fields. Then, click the [Apply] button.

Note

If the IP address or some other set value is invalid, the browser does not display the MMB Web-UI. In such cases,

connect the MMB console PC to the COM port on the MMB. Then, set the correct value.

3.3.7

Configuring telnet

Configure telnet for the MMB.

For details on how to back up the specified information, see

3.5 Saving Configuration Information

Note

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 3 Work before Operating System Installation

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Fujitsu PRIMEQUEST 1000 Series, Installation Manual, Page: 61 / 344

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews: