Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 181

Page: 181 / 344

2. Select [PSANIF] from the displayed list. Then, select [Properties] from the right-click menu.

Notes

- If there is no connection named [PSANIF], PSA has probably not been installed. Always change the

settings after PSA installation.

- Do not change the connection name [PSANIF]. Otherwise, the settings can be overwritten by the

automatically set values in a PSA update.

3. Select [Internet Protocol (TCP/IP)]. Then, click the [Properties] button.

>> The [Internet Protocol (TCP/IP) Properties] dialog box appears.

4. Set the IP address and subnet mask.

5. To apply the NIC settings for the dedicated PSA-to-MMB communication LAN, restart PSA by using the

following steps.

Select [Control Panel] - [Administrative Tools] - [Services].

Right-click [PRIMEQUEST Server Agent] in the right side of the window. Then, select [Restart].

Making settings through a remote desktop connection

To configure the PSA-to-MMB communication LAN through a remote desktop connection, you need a console

session connection. Establish this connection by using the following procedure.

1. Select [Start] - [Run].

>> The [Run] dialog box appears.

2. Enter "mstsc /v:<servername/ip address>/console" in the [Open] field. Then, click the [OK] button.

Specify the connected server name or the IP address in <servername/ip address>. (You cannot specify its

virtual IP address in the cluster.)

You can check the details of mstsc options by entering "mstsc /?".

6.3.2

Confirming management LAN settings

Make settings for the management LAN. If necessary, also configure any duplication with teaming or GLS, for

example.

After completing the above network settings for the management LAN, perform the operations in

6.3.7 Setting the

management LAN IP address

Note

In the PRIMEQUEST environment, it is necessary to specify OFF for the STP function of the switch that connects

to the management LAN used for communication with the MMB.

6.3.3

Setting the destinations of traps from a partition

For direct transfer of a PSA expansion trap from a partition, set the trap destination and PSA trap notification by

using the following procedure.

Remarks

- SNMPv3 is not supported in Windows.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 6 Work after Operating System Installation (PRIMEQUEST 1800E)

153

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands