Fujitsu MB95630H Series Hardware Manual Download | Manualshive

Page: 73 / 644

background image

MB95630H Series

MN702-00009-1v0-E

FUJITSU SEMICONDUCTOR LIMITED

53

CHAPTER 3 CLOCK CONTROLLER

3.5 Operations in Low Power Consumption

Mode (Standby Mode)

3.5.5

Watch Mode

In watch mode, only the subclock, the sub-CR clock and the watch prescaler
operate. The CPU and the operating clock for peripheral functions are stopped
in this mode.

■

Operations in Watch Mode

In watch mode, while retaining the contents of registers and RAM existing at the point

immediately before the device transits to watch mode, the device stops all functions except the

watch prescaler, external interrupt and low-voltage detection reset.

In the case of hardware watchdog timer, if it is enabled in standby mode by the non-volatile

register function, in watch mode, the sub-CR clock does not stop and the hardware watchdog

timer continues its operation. For details, see "CHAPTER 26 NON-VOLATILE REGISTER

(NVR) INTERFACE".

●

Transition to watch mode

If the clock mode monitor bits in the system clock control register (SYCC:SCM[2:0]) are

"0b000" or "0b100", writing "1" to the watch bit in the standby control register (STBC:TMD)

causes the device to transit to watch mode.

The device can transit to watch mode only when the clock mode is subclock mode or sub-CR

clock mode.

After the device transits to watch mode, if the pin state setting bit in the standby control

register (STBC:SPL) is "0", the states of the external pins are kept; if the SPL bit is "1", the

states of the external pins become high impedance (a pin is pulled up if the pull-up resistor

connection for that pin is selected in the pull-up register).

●

Release from watch mode

The device is released from watch mode by a reset, a watch interrupt, or an external interrupt.

With the deep standby mode control bit (STBC2:DSTBYX) set to "0", even after a reset occurs

or an interrupt is generated by a peripheral function, the device transits to sleep mode until the

Flash recovery wait time elapses.

However, if a program is being executed on the RAM, no Flash recovery wait time occurs.

Note:

If the device is released from watch mode by an interrupt, a peripheral function having
transited to time-base timer mode during operation resumes operating from the point at
which it transited to time-base timer mode. Therefore, some settings of that peripheral
function, such as the initial interval time of the interval timer, become undefined. Initialize
that peripheral function if necessary after releasing the device from watch mode.

«
...
71
72
73
74
75
...
»

Summary of Contents for MB95630H Series





































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MB95630H Series

Brand: Aastra Pages: 2

Brand: IDT Pages: 281

DMX-Universal-Demux

Brand: DMX4ALL Pages: 17

Brand: Rockwell Automation Pages: 108

Brand: LevelOne Pages: 31

HHM Series HHM2411

Brand: TDK Pages: 2

IPAM-1600s Series

Brand: C-Com Pages: 148

Brand: Tandy Pages: 24

Brand: Intel Pages: 26

Brand: Kaya Instruments Pages: 48

DTS 4020.timebridge

Brand: Mobatime Pages: 94

Brand: Rane Pages: 6

Fibe-Air IP-10G

Brand: Ceragon Pages: 71

Brand: Enterasys Pages: 2

EZ-KIT LITE ADSP-2191

Brand: Analog Devices Pages: 98

BreezeNET DS.11 Configuration Utility

Brand: Alvarion Pages: 2

com.tom INDUSTRY 100.WLAN.W

Brand: Beck Pages: 2

Brand: ZyXEL Communications Pages: 114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands