Fujitsu MB95630H Series Hardware Manual Download | Manualshive

Page: 520 / 644

background image

MB95630H Series

500

FUJITSU SEMICONDUCTOR LIMITED

MN702-00009-1v0-E

CHAPTER 24 I

2

C BUS INTERFACE

24.5 Interrupts

24.5

Interrupts

The I

2

C bus interface has a transfer interrupt and a stop interrupt which are

triggered by the following events.
• Transfer interrupt

A transfer interrupt occurs either upon completion of data transfer or when a
bus error occurs.

• Stop interrupt

A stop interrupt occurs upon detection of a stop condition or arbitration lost

or upon access to the I

2

C bus interface in stop/watch mode.

■

Transfer Interrupt

Table 24.5-1 shows the transfer interrupt control bits and I

2

C bus interface interrupt sources.

•

Interrupt upon completion of transfer

An interrupt request is output to the CPU upon completion of data transfer if the transfer
completion interrupt request enable bit has been set to enable (IBCR1n:INTE = 1). In the
interrupt service routine, write "0" to the transfer completion interrupt request flag bit
(IBCR1n:INT) to clear the interrupt request. When data transfer is completed, the
IBCR1n:INT bit is set to "1" regardless of the value of the IBCR1n:INTE bit.

•

Interrupt in response to a bus error

When the following conditions are met, a bus error is deemed to have occurred, and the I

2

C

bus interface will be stopped.

- When a stop condition is detected in master mode.

- When a start or stop condition is detected during transmission or reception of the first

byte.

- When a start or stop condition is detected during transmission or reception of data

(excluding the start, first data, and stop bits).

In these cases, an interrupt request is output to the CPU if the bus error interrupt request enable

bit has been set to enable (IBCR1n:BEIE = 1). In the interrupt service routine, write "0" to the

bus error interrupt request flag bit (IBCR1n:BER) to clear the interrupt request. When a bus

error occurs, the IBCR1n:BER bit is set to "1" regardless of the value of the IBCR1n:BEIE bit.

Table 24.5-1 Transfer Interrupt Control Bits and I

2

C Bus Interface Interrupt

Sources

Item

End of transfer

Bus error

Interrupt request flag bit

IBCR1n:INT =1

IBCR1n:BER =1

Interrupt request enable bit

IBCR1n:INTE =1

IBCR1n:BEIE =1

Interrupt source

Data transfer complete

Bus error occurred

«
...
518
519
520
521
522
...
»

Summary of Contents for MB95630H Series





































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MB95630H Series

Brand: ZALMAN Pages: 20

Brand: 3Com Pages: 2

Brand: 3Com Pages: 74

Brand: 3Com Pages: 6

Brand: ZyXEL Communications Pages: 215

Brand: UfiSpace Pages: 35

Brand: Point of View Pages: 13

Brand: Kontron Pages: 42

Brand: SurfControl Pages: 2

Brand: SeaLevel Pages: 21

Brand: ZALMAN Pages: 16

Brand: Softing Pages: 16

SecPath F50X0 Series

Brand: H3C Pages: 41

Brand: ADLINK Technology Pages: 86

EK-Quantum Vector FTW3 RTX 2080 Ti

Brand: ekwb Pages: 3

Brand: Patton electronics Pages: 8

Brand: TRENDnet Pages: 56

Brand: COMMUNICATIONS-APPLIED TECHNOLOGY Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands