manualshive.com logo in svg

Fujitsu MB90460 Series, Hardware Manual, Page: 557 / 739

Share
Download
Fujitsu MB90460 Series Hardware Manual Download Page 557

538

CHAPTER 19  DELAYED INTERRUPT GENERATOR MODULE

19.3

Operation of the Delayed Interrupt Generator Module

When software causes the CPU to write "1" to the relevant bit of DIRR, the request latch 
in the delayed interrupt generator module is set and an interrupt request is generated to 
the interrupt controller.

■

Operation of the Delayed Interrupt Generator Module 

When software causes the CPU to write "1" to the relevant bit of DIRR, the request latch in the delayed

interrupt generator module is set and an interrupt request is generated to the interrupt controller.  If the

priority of other interrupt requests is lower than that of this interrupt or no other interrupt request is

generated, the interrupt controller generates an interrupt request to the F

2

MC-16LX CPU.  The F

2

MC-

16LX CPU compares the ILM bit of the internal CCR register and the interrupt request.  When the request

level is higher than that of the ILM bit, the CPU starts the hardware interrupt processing microprogram

immediately after execution of the current instruction ends.  As a result, the interrupt processing routine for

this interrupt is executed.  This interrupt cause is cleared and task switching is done by writing "0" to the

relevant bit of DIRR in the interrupt processing routine.  Figure 19.3-1 Operation of the delayed interrupt

generator module shows the operation of the delayed interrupt generator module.

Figure 19.3-1  Operation of the Delayed Interrupt Generator Module

DIRR

ICR xx

ICR yy

CMP

ILM

IL

NTA

CMP

WRITE

Delayed interrupt generation module

Delayed interrupt controller

Other requests

F

2

MC-16LX CPU

Summary of Contents for MB90460 Series




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments