manualshive.com logo in svg

Fujitsu MB90460 Series, Hardware Manual, Page: 464 / 739

Share
Download
Fujitsu MB90460 Series Hardware Manual Download Page 464

445

CHAPTER 16  PWC Timer

16.5

PWC Timer Interrupts

The PWC timer is enabled to generate an interrupt request in an overflow of the counter 
or measurement terminated in pulse-width measurement mode.  It is also coordinated 

with the extended intelligent I/O service (EI

2

OS).

■

PWC Timer Interrupts

Table 16.5-1 lists the interrupt control bits and interrupt causes of the PWC timer.

In the PWC timer, the OVIR bit of the PWC control status register (PWCSL) is set to "1" by an overflow

(from FFFF

H

 to 0000

H

) of the up counter.  If an interrupt request is enabled (PWCSL:OVIE = 1) in this

operation, the interrupt request is output to the interrupt controller.

The EDIR bit of the PWC control status register (PWCSL) is set to "1" by measurement terminated in

pulse-width measurement mode.  If an interrupt request is enabled (PWCSL:EDIE = 1) in this operation,

the interrupt request is output to the interrupt controller.

■

PWC Timer Interrupts and EI

2

OS

Table 16.5-2 lists the PWC timer interrupts and EI

2

OS.

Table 16.5-1  Interrupt Control Bits and Interrupt Causes of the PWC Time

PWC timer 0

PWC timer 1

Interrupt request flag bit

PWCSL0: OVIR

PWCSL0: EDIR

PWCSL1: OVIR

PWCSL1: EDIR

Interrupt request enable bit PWCSL0: OVIE

PWCSL0: EDIE

PWCSL1: OVIE

PWCSL1: EDIE

Interrupt cause

Overflow of the 16-bit 
up counter

Measurement 
terminated in pulse-
width measurement 
mode

Overflow of the 16-bit 
up counter

Measurement 
terminated in pulse-
width measurement 
mode

Table 16.5-2  16-bit PWC Timer Interrupts and EI

2

OS

Channel

Interrupt 

number

Interrupt control register

Vector table address

EI

2

OS

Register 

name

Address

Lower

Middle

Upper

PWC timer 0

*1

 

#13 (0D

H

)

ICR01

0000B1

H

FFFFC8

H

FFFFC9

H

FFFFCA

H

O

PWC timer 1

*2

 

#24 (18

H

)

ICR06

0000B6

H

FFFF9C

H

FFFF9D

H

FFFF9E

H

*1:  The same interrupt number as that for 16-bit PPG timer 0 is assigned to PWC timer 0.
*2:  The same interrupt number as that for output compare channel 5 match is assigned to PWC timer 1.

Summary of Contents for MB90460 Series




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments