manualshive.com logo in svg

Fujitsu MB90460 Series, Hardware Manual, Page: 426 / 739

Share
Download
Fujitsu MB90460 Series Hardware Manual Download Page 426

407

CHAPTER 15  MULTI-PULSE GENERATOR

15.6.4

Operation of Data Transfer of Output Data Register

Eight methods can be used to transfer data from the Output Data Buffer Register 
(OPDBR) to the Output Data Register (OPDR) automatically, which are described in the 
following paragraphs. Each method is selected by setting the OPS2 to OPS0 bits in the 
Output Control Register (OPCR).

■

Operation of Data Transfer of Output Data Register

There are eight methods of data transfer from Output Data Buffer Registers (OPDBRB to OPDBR0) to the
Output Data Register (OPDR):

•

OPDBR0 Write

•

16-bit Reload Timer Underflow

•

Position Detection

•

Position Detection and 16-bit Reload Timer Underflow

•

Position Detection or 16-bit Reload Timer Underflow

•

One-shot Position Detection

•

One-shot Position Detection and 16-bit Reload Timer Underflow

•

One-shot Position Detection or 16-bit Reload Timer Underflow

The value of the Output Data Buffer Register (OPDBR) which is selected by the BNKF, RDA2 to RDA0
bits in Output Data Register (OPDR), is transferred to the Output Data Register (OPDR) when the write
signal is generated from the Data Write Control Circuit. However, at the time when OPS2 to OPS0 = 000

B

,

the value of OPDBR0 is always transferred to the Output Data Register (OPDR) in spite of the value of
BNKF, RDA2 to RDA0 bits. Figure 15.6-2 shows structure between OPDBRB to OPDBR0 registers  and
OPDR register.

Note:

 When the data transfer method is changed, the next Data Buffer Register to be selected is always
specified by the BNKF, RDA2 to RDA0 bits in the Data Output Register. This does not apply to the
OPDBR0 Write method, in OPDBR0 Write method BNKF, RDA2 to RDA0 bits are ignored. Word
access to Output Data Register must be used.

Figure 15.6-12  Structure between OPDBRB to OPDBR0 and OPDR Registers

12 TO 1 SELECTOR

TO OUTPUT 

OPDR

OPDBR0

WT

O

OP

S1

OP

S0

RDA

2

R

DA1

RDA

0

BNK

F

OPS

2

OPDBR1

OPDBR2

OPDBR3

OPDBR4

OPDBR5

OPDBR6

OPDBR7

OPDBR8

OPDBR9

OPDBRA

OPDBRB

CONTROL
CIRCUIT

Summary of Contents for MB90460 Series




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments