manualshive.com logo in svg

Fujitsu MB90460 Series, Hardware Manual, Page: 341 / 739

Share
Download
Fujitsu MB90460 Series Hardware Manual Download Page 341

322

CHAPTER 14  MULTI-FUNCTIONAL TIMER

■

16-bit Input Capture Interrupts

Table 14.5-5 lists the interrupt control bits and interrupt causes of the 16-bit input capture.

In the 16-bit input capture, the ICP0 to ICP3 bit of the input capture control register (PICSL01/ICSL23) is

set to "1" when valid edge is detected in IN0 to IN3.  If an interrupt request is enabled (PICSL01/

ICSL23:ICE0/ICE1 = 1) in this operation, the interrupt request is output to the interrupt controller.

■

16-bit Input Capture Interrupts and EI

2

OS

Table 14.5-6 lists the 16-bit input capture interrupts and EI

2

OS.

■

Waveform Generator Interrupts

 lists the interrupt control bits and interrupt causes of the waveform generator.

In the waveform generator, the TMIF bit of the 16-bit timer control register (DTCR0/DTCR1/DTCR2) is

set to "1" when 16-bit timer underflow and DTCR0/DTCR1/DTCR2:TMD2 to TMD0=000

B

 or 001

B

.  If an

interrupt request is enabled (DTCR0/DTCR1/DTCR2:TMIE = 1) in this operation, the interrupt request is

output to the interrupt controller.

Table 14.5-5  Interrupt Control Bits and Interrupt Causes of the 16-bit Input Capture 0 to 3

16-bit input capture 0/1

16-bit input capture 2/3

Interrupt request flag bit

PICSL01:ICP0/ICP1

ICSL23:ICP2/ICP3

Interrupt request enable bit

PICSL01:ICE0/ICE1

ICSL23:ICE2/ICE3

Interrupt cause

Valid edge is detected in IN0/IN1

Valid edge is detected in IN2/IN3

Table 14.5-6  16-bit Input Capture Interrupts and EI

2

OS

Channel

Interrupt 

number

Interrupt control register

Vector table address

EI

2

OS

Register 

name

Address

Lower

Middle

Upper

Input capture 0/1 

*1

#33 (21

H

)

ICR11

0000BB

H

FFFF78

H

FFFF79

H

FFFF7A

H

O

Input capture 2/3 

*2

#35 (23

H

)

ICR12

0000BC

H

FFFF70

H

FFFF71

H

FFFF72

H

*1:  The same interrupt control register as that for 16-bit input capture 0/1 is assigned to 16-bit free-run timer compare clear.
*2:  The same interrupt control register as that for 16-bit input capture 2/3 is assigned to Time-base timer.

Table 14.5-7  Interrupt Control Bits and Interrupt Causes of the Waveform Generator

Waveform generator

16-bit timer 0/1/2

DTTI0

Interrupt request flag bit

DTCR0/DTCR1/DTCR2:TMIF

SIGCR:DTIF

Interrupt request enable bit

DTCR0/DTCR1/DTCR2:TMIE

--

Interrupt cause

16-bit timer 0/1/2 underflow

Low level is detected in DTTI0

Summary of Contents for MB90460 Series




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments