Fujitsu IP Centrex SRS-12i Administrator'S Manual Download Page 50

Page: 50 / 69

6-1

Fujitsu

IP Centr

ex T

elephone

Master Clear & Paswwor

d Reset

CHAPTER 6 – MASTER CLEAR & PASSWORD RESET

Master Clear (Option 96)

WARNING:
Master Clear will remove all programmed numbers,
password, and settings

In order to invoke the Master Clear, follow the steps below:

1. Press OPTIONS, numeric key “9”, “6”, then ENTER.

2. Enter 8 digits of numeric password (see Administrator Password

Registration in chapter 4).

* Factory Default Administrator Password - 99999999

3. Press ENTER.

4. If you select 1 for YES, the set will start initializing then the following

screen will appear.

If you select 2 for NO, the set will go back to the option menu screen.

Press either asterisk (*) to go back to sub-menu or OPTIONS to exit the option
menu.

PASSWORD RESET

If you misplaced your password, but you do not wish to invoke a Master
Clear, contact your System Administrator or call Fujitsu Technical Assistance
at 800-228-4736.

MASTER CLEAR

ENTER ADM PASSWORD
********

MASTER CLEAR
(1: YES 2: NO) ->

MASTER CLEAR
COMPLETED

1: ONE-TOUCH

2: CALENDAR

3: INITIAL

(SELECT 1-29)

Summary of Contents for IP Centrex SRS-12i






































































Search results

Summary of Contents for IP Centrex SRS-12i

Reviews:

Related manuals for IP Centrex SRS-12i

Brands by name

Popular brands

Fujitsu IP Centrex SRS-12i, Administrator'S Manual

Search results

Summary of Contents for IP Centrex SRS-12i

Reviews:

Related manuals for IP Centrex SRS-12i

Brands by name

Popular brands