Fujitsu Fujitsu fi-5950 Operator'S Manual Download Page 123

Page: 123 / 257

103

DAILY CARE

This chapter describes how to clean the scanner.

4.1 Cleaning Materials and Areas Requiring Cleaning .........104

4.2 Cleaning the Pad ................................................................106

4.3 Cleaning the Rollers (using the cleaning sheet) .............107

4.4 Cleaning the Rollers (with a lint-free cloth) ..................... 110

4.5 Cleaning the Transport path and the sensors ................. 114

WARNING

•

Take care not to pinch your fingers inside the

ADF.

•

The glass inside the ADF becomes hot during

operation. Be careful not to get burned.

Summary of Contents for Fujitsu fi-5950


































































































































































































































































Search results

Summary of Contents for Fujitsu fi-5950

Reviews:

Brands by name

Popular brands

Fujitsu Fujitsu fi-5950, Operator'S Manual

Search results

Summary of Contents for Fujitsu fi-5950

Reviews:

Brands by name

Popular brands