Fujitsu fi-7300NX Operator'S Manual Download Page 158 | Manualshive

Page: 158 / 321

background image

If the problem persists, write down the error code and contact the distributor/dealer where you purchased
this product. Refer to the contact information in the Contact List if supplied with this product, or refer to
the contact information in the Contact for Inquiries section if provided in Safety Precautions supplied with
this product, and then make an inquiry.

For M5:A5

Try again later.

Authentication Failed

If the authentication for PaperStream NX Manager fails, the [Error] screen on the touch screen displays the
following code.

M6:AF Authentication failed in Auto Login mode. Check the Auto Login Setting.

Check the message displayed in the [Error] screen, and correct the following settings:

●

[Auto Login] setting on the scanner

●

Authentication setting for PaperStream NX Manager

To check the network settings for the scanner, press the [Set] button.
If the problem persists, write down the error code and contact the distributor/dealer where you purchased this
product. Refer to the contact information in the Contact List if supplied with this product, or refer to the contact
information in the Contact for Inquiries section if provided in Safety Precautions supplied with this product, and
then make an inquiry.

Troubleshooting

158

«
...
156
157
158
159
160
...
»

Summary of Contents for fi-7300NX


































































































































































































































































































































Reviews:

No comments

Related manuals for fi-7300NX

Brand: Leuze Pages: 15

Brand: Faro Pages: 51

OK 300 Hybrid Color

Brand: Zeutschel Pages: 68

Brand: ION Pages: 1

Brand: AbiSee Pages: 11

Brand: Kodak Pages: 43

8412447 - I55 - Document Scanner

Brand: Kodak Pages: 93

Digital Science 9520

Brand: Kodak Pages: 139

Brand: Datalogic Pages: 40

Brand: Jireh Pages: 141

OPTICPRO 12000P TURBO

Brand: Plustek Pages: 38

Brand: Hasselblad Pages: 36

XDM5205DWU - DocuMate 520

Brand: Xerox Pages: 73

Brand: Sage Pages: 2

Brand: VITALITY CHECK Pages: 9

Brand: Avision Pages: 64

Brand: Makita Pages: 68

Brand: Makita Pages: 195

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands