Fujitsu fi-7300NX Operator'S Manual Download Page 155 | Manualshive

Page: 155 / 321

background image

Sensor Error

Sensor Error

If a sensor error occurs, the [Error] screen on the touch screen displays one of the following codes.

L0:11 Sensor error

If the problem persists after turning the power back on, please inform your service provider of the error
code below.
Code L0:11

L2:13 Sensor error

If the problem persists after turning the power back on, please inform your service provider of the error
code below.
Code L2:13

L6:1B Sensor error

If the problem persists after turning the power back on, please inform your service provider of the error
code below.
Code L6:1B

Take the following measures.

●

Clean the ultrasonic sensors and the document sensors by referring to

Cleaning the Inside of the Scanner

(ADF) with a Cloth (page 121)

●

Turn the scanner off then back on.

If the problem persists, write down the error code and contact the distributor/dealer where you purchased this
product. Refer to the contact information in the Contact List if supplied with this product, or refer to the contact
information in the Contact for Inquiries section if provided in Safety Precautions supplied with this product, and
then make an inquiry.

Troubleshooting

155

«
...
153
154
155
156
157
...
»

Summary of Contents for fi-7300NX


































































































































































































































































































































Reviews:

No comments

Related manuals for fi-7300NX

IMAGECLASS MF4150

Brand: Canon Pages: 76

TellerScan 220E

Brand: Digital Check Pages: 18

Brand: OEG Pages: 32

Brand: Reinecker Pages: 28

Brand: Hasselblad Pages: 2

Brand: Design Technology Pages: 4

Uniden BC80 XLT

Brand: Racing Electronics Pages: 32

Brand: Xerox Pages: 105

Brand: Uniden Pages: 32

Brand: patura Pages: 40

Brand: Unitech Pages: 34

Brand: Ferm Pages: 88

fi 5750C - Document Scanner

Brand: Fujitsu Pages: 167

Brand: Fujitsu Pages: 180

FI 6140 - Document Scanner

Brand: Fujitsu Pages: 226

Brand: Fujitsu Pages: 96

ScanSnap iX1500

Brand: Fujitsu Pages: 14

SCANSNAP iX1400

Brand: Fujitsu Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands