Fujitsu FI-5900C Operator'S Manual Download

Page: 127 / 257

107

DAILY CARE

This chapter describes how to clean the scanner.

4.1 Cleaning Materials and Areas Requiring Cleaning .........108

4.2 Cleaning the Pad ................................................................ 110

4.3 Cleaning the Rollers (using the cleaning sheet) ............. 111

4.4 Cleaning the Rollers (with a lint-free cloth) ..................... 114

4.5 Cleaning the Transport path and the sensors ................. 118

WARNING

•

Take care not to pinch your fingers inside the

ADF.

•

The glass inside the ADF becomes hot during

operation. Be careful not to get burned.

Summary of Contents for FI-5900C


































































































































































































































































Search results

Summary of Contents for FI-5900C

Reviews:

Related manuals for FI-5900C

Brands by name

Popular brands

Fujitsu FI-5900C, Operator'S Manual

Search results

Summary of Contents for FI-5900C

Reviews:

Related manuals for FI-5900C

Brands by name

Popular brands