Fujitsu F2MC-8FX Series User Manual Download Page 85

Page: 85 / 110

AN07-00200-03E

5.3

LIN communication flow

In general LIN communication, one master communicates with numerous slaves. LINs, which adopt

a bus topology, connect the master and all the slaves using a single wire, so header electrical signals

sent by the master are transmitted by the wire to all the slaves. The slaves check the frame ID, and if

the header is addressed to them, sent a response to the master according to the content received. If

the header received is addressed to another slave, it is ignored. In this way, 1-to-1 communication

between the master and each slave is achieved.

This section explains the actual trading of communications. Currently, functions are allocated to

each of the slaves from 1 to 15.The master first communicates with slave 1 and turns the motor ((1)

in Figure 5-5 Main LIN network configuration and Figure 5-6 Example of communication sequence

between the master and slaves during normal communication), and next acquires sensor information

by communicating with slave 3. ((2) in “Figure 5-5 Main LIN network configuration” and Figure 5-6

Example of communication sequence between the master and slaves during normal communication.)

Thereafter, the motor is turned by communications with slave 2 ((3) in Figure 5-5 Main LIN network

configuration and Figure 5 6 Communications sequence between master and slave during normal

communications).The master acquires sensor information from slave 3 again ((4) in Figure 5-5 Main

LIN network configuration and Figure 5 6 Communications sequence between master and slave

during normal communications), and finally turns ON the lamp by communicating with slave 15 ((5)

in Figure 5-5 Main LIN network configuration and Figure 5 6 Communications sequence between

master and slave during normal communications).In this chain of communications, communications

between the master and slaves 2 and 3 are contiguous, and the master processes the motor turning by

communicating with slave 2 using sensor information acquired by communicating with slave 3 first.

In this way, during actual communications the master and multiple slaves repeatedly communicate

on a 1-to-1 basis.

Summary of Contents for F2MC-8FX Series















































































































Search results

Summary of Contents for F2MC-8FX Series

Reviews:

Fujitsu F2MC-8FX Series, User Manual, Page: 85 / 110

Search results

Summary of Contents for F2MC-8FX Series

Reviews: