manualshive.com logo in svg

Fujitsu ETERNUS AF650 S2, Basic Operation Manual

Share
Download
Fujitsu ETERNUS AF650 S2 Basic Operation Manual Download Page 16

LED name

LED status

Meaning

BCA
(BCU Alarm)

 (amber)

The battery is in error status.

BTA
(BTU Alarm)

 (amber)

The battery is in error status.

1.1.4

Components (Rear)

This section describes the controllers and the power supply units in the rear of the controller enclosure.

■

Controller

The controller contains a CPU, system memory, host interfaces, Bootup and Utility Device (BUD), and drive
interface (DI) ports. The controller controls all operations in the ETERNUS AF.

●

Controller

Figure 1.6

 shows the controller.

Figure 1.6 Controller

1

3

2

4

7

9

5 6

8

1.

Host interface (CA#0)
Install host interfaces. For details, refer to 

"■ Host Interfaces" (page 18)

.

2.

Host interface (CA#1)
Install host interfaces. For details, refer to 

"■ Host Interfaces" (page 18)

.

3.

Host interface (CA#2)
Install host interfaces. For details, refer to 

"■ Host Interfaces" (page 18)

.

4.

Host interface (CA#3)
Install host interfaces. For details, refer to 

"■ Host Interfaces" (page 18)

.

5.

FST (LAN) port
A port that is dedicated for maintenance engineers. Customers must not use this port.

6.

RMT (LAN) port
This port is used for connecting a LAN cable and used for the remote support function. This port uses an
RJ-45 connector.

7.

MNT (LAN) port
This port is used for connecting a LAN cable and used for operation management. This port uses an RJ-45
connector.

8.

DI (OUT) port
This port is used to connect a controller enclosure to a drive enclosure with a mini SAS HD cable between
enclosures.

Chapter 1 Component Names and LED Names
1.1 Controller Enclosures
 

16

FUJITSU Storage ETERNUS AF650 S2, ETERNUS AF650 All-Flash Arrays Operation Guide (Basic)

Copyright 2017 FUJITSU LIMITED

P3AG-1932-04ENZ0

Summary of Contents for ETERNUS AF650 S2




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands