Fujitsu D2619 Technical Manual Download Page 26 | Manualshive

Page: 26 / 36

background image

26

Technical Manual

D2619 (RX/TX300 S5)

Temperature/system monitoring

Features

Fan control

The fans are regulated according to temperature.

Sensor monitoring

The removal of, or a fault in, a temperature sensor is detected. Should this
happen all fans monitored by this sensor run at maximum speed, to achieve the
greatest possible protection of the hardware.

Voltage monitoring

When voltage exceeds warning level high or falls below warning level low an
alert will be generated.

System Event Log (SEL)

All monitored events of the system board are signalized via the Global Error
LED and recorded in the System Event Log. They could be retrieved in the BIOS
Setup or via ServerView.

Diagnostic LEDs

For signalisation of failures LEDs are situated on the system board.

«
...
24
25
26
27
28
...
»

Summary of Contents for D2619





































Reviews:

No comments

Related manuals for D2619

Brand: JETWAY Pages: 2

Fatal1ty 990FX Professional

Brand: ASROCK Pages: 287

Brand: Nuvoton Pages: 5

Z270 Gaming Pro Carbon Motherboard

Brand: MSI Pages: 92

Brand: Zotac Pages: 56

Brand: EVGA Pages: 80

Brand: Arbor Technology Pages: 86

Brand: Ublox Pages: 38

NORA-W10 Series

Brand: Ublox Pages: 22

Brand: Inrevium Pages: 57

Brand: Ublox Pages: 42

Brand: Commell Pages: 53

Brand: Texas Instruments Pages: 20

HBJC390F841VAG34B

Brand: JETWAY Pages: 44

Brand: Microsemi Pages: 22

Brand: JETWAY Pages: 47

ConnectCore 6UL SBC Pro

Brand: Digi Pages: 54

Brand: ASROCK Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands