background image

Internal ports and connectors

A26361-D1527-Z120-1-6319

English - 9

Graphics port - Supported screen resolutions

Depending on the operating system used, the screen resolutions in the following table refer to the
mainboard screen controller.

If you are using an external screen controller, you will find details of supported screen resolutions in
the operating manual or technical manual supplied with the controller.

Screen resolution

Refresh rate (Hz)

bpp

Colour

640 x 480

120

32

32 bit

800 x 600

120

32

32 bit

1024 x 768

100

32

32 bit

1280 x 1024

100

32

32 bit

1600 x 1200

100

32

16 bit

1920 x 1440

75

32

16 bit

2048 x 1536

60

32

16 bit

Internal ports and connectors

The positions of the internal ports and connectors are shown on the Cover. Additional information on
some ports is also provided here.

Hard disk connection

An ultra ATA/66 or ultra ATA/100 hard disk must be connected with a cable especially designed for
the ultra ATA/66 or ultra ATA/100 mode.

Ê

 

Connect the end of the cable marked with blue to the mainboard.

All manuals and user guides at all-guides.com

Summary of Contents for D1526













































Reviews: