Fujitsu AOU18RLXFW Service Instructions Manual Download Page 19

Page: 19 / 66

22. VARIOUS PROTECTIONS

1. DISCHARGE GAS TEMPERATURE OVERRISE PREVENSION CONTROL

The discharge gas thermosensor (discharge thermistor : Outdoor side) will detect discharge gas

temperature.

ASU18/ 24RLF

219.2°F

(104°C)

213.8°F

(101°C)

230°F

(110°C)

When the discharge temperature becomes higher than Temperature ,the compressor frequency

is decreased 10rps, and it continues to decrease the frequency for 10rps every 120 seconds until

the temperature becomes lower than Temperature .

When the discharge temperature becomes lower than Temperature , the control of the control of

the compressor frequency is released.
When the discharge temperature becomes higher than Temperature ,the compressor is stopped

and the indoor unit LED starts blinking.

(Table19 : Discharge Temperature Over Rise Prevension Control / Release Temperature)

Temperature

2. CURRENT RELEASE CONTROL

The compressor frequency is controlled so that the outdoor unit input current does not exceeds

the current limit velue that was set up with the outdoor temperature.

The compressor frequency returns to the designated frequency of the indoor unit at the time

when the frequency becomes lower than the release value.

(Table20 : Current Release Operation Value / Release Value)

01-16

[ Heating ]

OT (Control / Release)

10.0A/ 9.5A

11.5A/ 11.0A
13.0A/ 12.5A
13.0A/ 12.5A

11.0A/ 10.5A

13.0A/ 12.5A
15.0A/ 14.5A
15.0A/14.5A

62.6°F(17°C)

53.6°F(12°C)

OT : Outdoor Temperature

41°F(5°C)

62.6°F(17°C)

53.6°F(12°C)

41°F(5°C)

ASU18RLF

OT (Control / Release)

OT : Outdoor Temperature

ASU24RLF

OT (Control / Release)

10.0A/ 9.5A

12.5A/ 12.0A
12.5A/ 12.0A

10.0A/ 9.5A

13.0A/ 12.5A
14.5A/ 14.0A

114.8°F(46°C)

104°F(40°C)

114.8°F(46°C)

104°F(40°C)

OT : Outdoor Temperature

ASU18RLF

OT (Control / Release)

OT : Outdoor Temperature

ASU24RLF

[ Cooling ]

122°F(50°C)

9.0A/ 8.5A

Summary of Contents for AOU18RLXFW



































































Search results

Summary of Contents for AOU18RLXFW

Reviews:

Brands by name

Popular brands

Fujitsu AOU18RLXFW, Service Instructions Manual

Search results

Summary of Contents for AOU18RLXFW

Reviews:

Brands by name

Popular brands