Fujitsu AO G14KBTA2 Series Service Instruction Download Page 39

Page: 39 / 47

Trouble shooting 36

Forecast of Cause:

Check Point 2 : Check external cause at Indoor and Outdoor (Voltage drop or Noise)

Check Point 1 : Check indoor and outdoor installation condition

Check Point 3 : Check Wired Remote Controller and Controller PCB

No Operation (Power is ON)

1. Setting/ Connection failure 2. External cause

3. Electrical Component defective

Indoor Unit - Check incorrect wiring between Indoor Unit - Remote Control.

Or, check if there is an open cable connection.

Are these Indoor Unit, Outdoor Unit, and Remote Control suitable model numbers to connect?

>> If there is some abnormal condition, correct it by referring to Installation manual and

Data & Technical Manual.

Turn off Power and check/ correct followings.

Is there loose or removed communication line of Indoor Unit and Outdoor Unit?

Instant drop ----- Check if there is a large load electric apparatus in the same circuit.

Momentary power failure ----- Check if there is a defective contact or leak current in the power supply circuit.

Noise ----- Check if there is any equipment causing harmonic wave near electric line.

(Neon bulb or electric equipment that may cause harmonic wave)

Check the complete insulation of grounding.

>> If the symptom does not change by above Check 1, 2, 3, replace Main PCB of Outdoor unit.

02-37

Check Voltage at CN300 of Controller PCB. (Terminal 1-3, Terminal 1-2)

(Power supply for the Remote Control)

Check Voltage at CN300 (Terminal 1-2) of UTY-TWRXZ2 (Communication kit).

(Power supply to Remote control)

For AS* G __ KGTB

>> If it is DC12V, Remote control is failure. (Controller PCB is normal)

>> Replace Remote control

>> If it is DC 0V, Controller PCB is failure. (Check Remote control once again) >> Replace Controller PCB

Check Voltage at CNC01 (Terminal 1-3) of UTY-TWBXF2 (Communication kit).

(Power supply to Remote control)

For AS* G __ KMTB

For AR type

For AU type

>> If it is DC13V, Remote control is failure. (Controller PCB is normal)

>> Replace Remote control

>> If it is DC 0V, Controller PCB is failure. (Check Remote control once again) >> Replace Controller PCB

>> If it is DC13V, Remote control is failure. (Controller PCB is normal)

>> Replace Remote control

>> If it is DC 0V, Controller PCB is failure. (Check Remote control once again) >> Replace Controller PCB

Check Voltage at CN14 of Controller PCB. (Terminal 1-3, Terminal 1-2)

(Power supply for the Remote Control)

>> If it is DC12V, Remote control is failure. (Controller PCB is normal)

>> Replace Remote control

>> If it is DC 0V, Controller PCB is failure. (Check Remote control once again) >> Replace Controller PCB

Summary of Contents for AO G14KBTA2 Series
















































Search results

Summary of Contents for AO G14KBTA2 Series

Reviews:

Related manuals for AO G14KBTA2 Series

Brands by name

Popular brands

Fujitsu AO G14KBTA2 Series, Service Instruction

Search results

Summary of Contents for AO G14KBTA2 Series

Reviews:

Related manuals for AO G14KBTA2 Series

Brands by name

Popular brands