1. Press the
button.
Select “OFF TIMER” or “ON TIMER”.
2. Press the
/
button.
Adjust the OFF or ON TIME.
To set the remote con-
troller in the holder
1. Insert.
2. Press in.
To take out the remote
controller from the
holder
1. Slide up.
2. Pull out.
Press the MANUAL AUTO button on the main
unit control panel.
To stop operation, press the MANUAL AUTO button again.
Use the MANUAL AUTO operation when the remote
controller is lost or unavailable.
To set or change the SLEEP Timer
1. Press the
button.
2. Press the
/
button.
Adjust the OFF TIME.
To cancel the SLEEP Timer
Press the
button.
Select “TIMER RESET”.
The air conditioner will return to normal operation.
To set or change the PROGRAM Timer
1. Press the
button.
Select “OFF TIMER”.
2. Press the
/
button.
Adjust the OFF time.
3. Repeat Step 1 and 2 to adjust ON time.
4. Press the
button.
Select “PROGRAM TIMER”.
(If the ON timer has been selected to operate
first, the unit will stop operating at this point.)
To cancel the PROGRAM Timer
Press the
button.
Select “TIMER RESET”.
The air conditioner will return to normal operation.
(1) The remote controller must be pointed at signal receiver to operate correctly.
(2) Operating range : About 7 meters.
(3) Beeping sound
• When a signal is properly received by the air conditioner, a beeping sound will be
heard twice.
• If an invalid signal is received by the air conditioner, a beeping sound will be heard 5
times.
• If no beeping sound is heard, press the remote controller button again.
(4) The buttons except the SLEEP, TIME ADJUST and ACL buttons can only be selected
while in operation mode.
PREPARATION
OPERATION
CLEANING AND CARE
1
2
3
START/STOP
TIME ADJUST ACL
SET
SWING
SET
SWING
1, 3
2
1. Press and slide
the lid.
2. Insert batteries.
Be sure to follow the
polarity markings indi-
cated in the compart-
ment.
3. Slide back the lid.
1. Press the TIME
ADJUST button.
2. Press the
/
button.
3. Press the TIME
ADJUST button.
1. Push the intake grille’s hooks inward towards
the center of the unit to open the intake grille.
2. Pull out the filter from the intake grille.
3. Clean the air filters.
Remove the dust from the air filters by vacuuming or washing
them. After washing, be sure to allow it to dry thoroughly in a
shady place before reinstalling.
4. Re-attach the air filters to the intake grille.
1
Replace the air filter into its holder.
2
Make sure that the air filter makes contact with the filter
stopper when it is replaced into its holder.
5. Close the intake grille and push the intake grille’s
hooks outward.
• When used for extended periods, the unit may accumulate dirt
inside, reducing its performance. We recommend that the unit
be inspected regularly, in addition to your own cleaning and
care.
For more information, consult authorized service personnel.
• Dust can be cleaned from the air filter either with a vacuum
cleaner, or by washing the filter in a solution of mild detergent
and warm water.
• When cleaning the unit, do not use water hotter than 40 °C,
harsh abrasive cleansers, or volatile agents like benzene or
thinner.
• Do not expose the unit to liquid insecticides or hairsprays.
• During periods of normal use, the air filters should be cleaned
every two weeks.
• When shutting down the unit for one month or more, first allow
the fan mode to operate continuously for about one-half day to
allow internal parts to dry thoroughly.
Each press of the
START/STOP
button alternates
operation and stop.
Press the
MASTER
CONTROL
button while in operation.
Press the
/
button while in operation.
Press the
FAN
CONTROL
button while in operation.
Press the
SET
button while in operation.
For swing operation:
Press the
SWING
button while in operation.
Stop the setting by pressing it again.
Press
• Each press of the MANUAL AUTO button alternates
operation and stop.
• When the air conditioner is operated from the main
unit, it will operate under the same conditions as the
AUTO mode is selected on the remote controller.
• The fan speed is selected to “AUTO” and the tempera-
ture setting will be set to 23 °C.
(Select HEAT or
COOL automatically.)
Temperature setting range
AUTO • • • • • • • 18 to 30 °C
HEAT • • • • • • • 16 to 30 °C
COOL/DRY • • • 18 to 30 °C
The thermostat setting should be considered a stan-
dard value, and may differ somewhat from the ac-
tual room temperature.
Range of swing
The range of swing is relative to the currently
set airflow direction.
(Select the fan speed
automatically.)
1
2
1
2
LOAD BATTERIES (R03/LR03 x 2)
SET THE CURRENT TIME
REMOTE CONTROLLER HOLDER
MANUAL AUTO OPERATION
SLEEP TIMER
MASTER CONTROL
TEMPERATURE
AIR DIRECTION (UPPER AND LOWER)
FAN SPEED
ON / OFF TIMER
PROGRAM TIMER
CLEANING THE AIR FILTER
AUTO COOL DRY FAN HEAT
NOTES
AUTO HIGH MED LOW
RESET
OFF TIMER
ON TIMER
PROGRAM TIMER (OFF
ON, OFF
ON)
(5) PROGRAM timer
• The PROGRAM timer allows you to integrate OFF timer and ON timer operations
in a single sequence.
• The first timer function to operate will be the one set nearest to the current time.
(6) SLEEP timer
To prevent excessive warming or cooling during sleep, the SLEEP timer function au-
tomatically modifies the set temperature in accordance with the time setting. When
the set time has elapsed, the air conditioner completely stops.
(7) When connecting with other remote controllers, the indoor unit might be controlled by
the other remote controllers.
(8) The wired remote controller or the simple remote controller can also be used with this
unit.
NOTES
NOTES
NOTES
NOTES
NOTES
NOTES
NOTES
SWING
TIMER OPERATION
MANUAL
AUTO
Grille Hook
Air filter
Grille Hook
Air Filter
Filter Holder
Intake Grille
Filter Stopper
1
2
3
4
START / STOP
START/STOP
TIME ADJUST ACL
SET
SWING
SET
SWING
FAN
CONTROL
MASTER
CONTROL
SET
TEMP.
SET
TIME
