Fujitsu AIRSTAGE UTY-ASGXZ1 Operating Manual Download Page 9

Page: 9 / 141

Safety precautions

1-1

Before using Service Tool, read this “Safety precautions” thoroughly to ensure the correct

•

operation.
This section describes the important safety information to operate Service Tool.

•

The meanings of “WARNING” and “CAUTION” are explained as follows.

•

WARNING

This mark indicates the procedures, which might result in the
death of or serious injury to the user or service personnel if im-
properly performed.

CAUTION

This mark indicates the procedures, which might result in personal
harm to the user or damage to property if improperly performed.

This manual is for service personnel authorized to use the Service Tool. Always keep
this manual in an easily accessible place for use by authorized service personnel.

WARNING

When using U10 USB Network Interface, follow the instructions given in the manual

that comes with the product.

CAUTION

Service Tool can control the air-conditioner system on a personal computer. Be careful not

to turn off the power supply of the personal computer, or not to finish the application com

pulsorily during operation. Otherwise, Service Tool might malfunction. For personal com-
puter used as Service Tool, refer to the setting manual.

Summary of Contents for AIRSTAGE UTY-ASGXZ1














































































































































Search results

Summary of Contents for AIRSTAGE UTY-ASGXZ1

Reviews:

Related manuals for AIRSTAGE UTY-ASGXZ1

Brands by name

Popular brands

Fujitsu AIRSTAGE UTY-ASGXZ1, Operating Manual

Search results

Summary of Contents for AIRSTAGE UTY-ASGXZ1

Reviews:

Related manuals for AIRSTAGE UTY-ASGXZ1

Brands by name

Popular brands